lamber F92-ek Bedienungsanleitung Seite 22

Endless cycle (maximum 15 minutes) : the door
-
being closed and the cycle put on (any cycle), keep the
button "B" pressed for 3 seconds: lamps 1 and 2 will
flash at the same time (thermocontrol excluded); the
cycle can be interrupted at any time pressing again
button "C" that will let final sequences of pause-rinse
start.
Self-cleaning cycle :
- To switch the machine off press and hold button "A"
for 2 seconds
(Cycle pushbutton is red);
- Remove the overflowpipe from the tank and wait until
it is completely empty
(for machines equipped with drain pump, see the
relative section for instructions),
- Close the door of the dishwasher
- To switch the machine on
switch "A" for 2 seconds The "C" indicator flashes
yellow
-To begin the self-cleaning process, press and hold
cycle pushbutton "C" for 3 seconds until a solid purple
light turns on,.
After 10 minutes the machine will automatically stop
The "C" indicator light is solid red ;
N.B.: The indicator will switch off
seconds
-Stand by: The machine will automatically stop after
an hour of inactivity (red button "C" will stay lit) .
To resume normal function press the button "A".
DISHES POSITIONING
It is suitable to place dishes, inside the plastic basket
with the concave side facing upwards. Place mixed
cutlery in a vertical position into the suitable container
minding not to cram them and with handgrips towards
the bottom (see drawing).
ACHIEVEMENTS
Any deficiency in the washing process is apparent
when dirty residuals are visible. An insufficient rinsing
might cause any halos: in this case, check that the
rinsing jets are clean and there is a sufficient pressure
in the water distribution network (ideal is between 2-4
bar).
In the case that residuals are present, check that:
• the washing jets are clean
• there is detergent
• filters are clean
• the position of the dishes in the rack is correct (look
at the specific paragraph).
press and hold main
after nearly 15
RINSING ADDITIVES
To grant a perfect rinsing, a quick drying and to avoid
calcareous sediments on glasses and cups you must
add a surfactant on water (Brightener).
Your cleansing agent supplier will be able to suggest
the most suitable product. Your machine is equipped
with a rinse aid dispenser. Mean concentration used
is 0,15 g/liter.
REGENERATING
(for machines with Water softener)
If the glass-washer is equipped with a Water softener
the regeneration of resins is automatic according to
parameters fixed by the producer (this operation is
signalled by lighting up of led "D").
According to the water hardness, it is possibile to
modify the programming of the regeneration. See the
corresponding table in the installer section.
SALT CONTROL
When it is necessary to add salt in the container, the
lamp "D" flashes.
Unscrew the plug of the salt container at the bottom of
the tank and put 1 kg coarse salt tablets in it. Clean the
gasket and screw the plug.
Attention!
The lack of salt in the container damages the machine
because of limestone, besides a defective washing of
glasses and dishes.
These damages are not covered by the warranty.
DRAIN PUMP INSTRUCTION
(only for machines with drain pump)
The drain pump starts up automatically just during
the washing cycle to drain the exceeding water
coming from the rinsing cycle.
At the end of the working day, in order to
completely drain the tank, it is necessary to perform
the following operations:
1.Switch the machine off by keeping pressed the main
switch "A" for 2 seconds (cycle pushbutton
becomes red);
2.Open the door of the dishwasher;
3 .Remove the overflow from the tank;
4.Afterwards push
Pushbutton "C" flashes with sky-blue colour.
The drain will stop automatically after 5 minutes (cycle
pushbutton is red).
N.B : the button turns off completely after about 15"
seconds.
To stop manually the drain cycle,
button "C" again.
Reinstall the overflow and close the door.
22
button "C" for 3 seconds.
press the cycle