Maintenance - Moulinex Odyssey 2000 A DZ2 Gebrauchsanleitung

total capacity of the tank (K) at maximum.
Do not add any further water.
- Close the hatch or replace the "Master
Spray" assembly (depending on model).
Note: Never fill the tank (K) via the opening in
the "Pro Calc System" cassette (L) at the rear
of the tank.
. Getting started:
- Plug in the iron.
- Select the temperature of the soleplate with
4
the temperature adjustment control (H).
The temperature control indicator (I) will come
on; it will go out once the selected temperature
has been reached.
On first use, a little smoke may be given off by
the soleplate of the iron. This is temporary and
does not mean there is anything wrong with
the iron. This should not happen again.
. Steam ironing:
5
You have 2 steam flow positions:
Steam ironing is only possible in the steam
zone (.. to MAX). To obtain steam, position the
temperature adjustment control (H) in this
zone.
- Before commencing your ironing, wait for the
adjustment indicator (I) to go out and check
(depending on model) that the "Thermo
Sensor" indicator (J) has gone out.
- Select the steam flow rate using the steam
control (G).
Important:
To prevent any water dripping onto your
laundry, this iron is equipped with an "anti-
drip" system which shuts off the flow of water
as soon as the soleplate falls below a certain
temperature.
. Pressing
One push on the pressing button (F) allows
you to obtain a very powerful jet of steam
instantly.
- Never exceed 5 pushes in succession,
otherwise your iron may drip water from the
soleplate.
- Always use this function in the steam zone
indicated on the temperature adjustment
control (H).
When using the pressing function for the first
time, small deposits of limescale may come
out of the holes in the soleplate with the jet of
steam. So we recommend that you do not
carry out the first pushes directly over your
laundry.
. Vertical removal of creases (depending
6
on model):
You have the option of using your iron in the
vertical position to remove creases from
garments on hangers, curtains, etc...
- Set the temperature adjustment control (H)
to MAX.
- Hold the iron vertically close to the fabric,
without touching it leave at least a 2'' gap.
- Push the pressing button (F) at the rate of
not more than once per second.
The steam produced is not always visible but
it still has the ability to remove creases.
You can push the button up to 5 times in
succession.
Important:
- Do not use this function for synthetic fibres.
- Keep the iron at a sufficient distance from
the fabric to avoid any risk of scorching.
- The steam produced is very hot, so never
remove creases from a garment when a
person is wearing it; it must be on a hanger.
. Dry ironing:
or
- Set the steam control (G) to position
. Spray:
- Push on the spray button (E) in pulses. A
spray of cold water allows you to dampen
your laundry in both dry and steam position.
Very effective for removing creases.
. "Thermo Sensor" indicator (J) (depending
7
on model)
The indicator (J) situated at the front of the
handle of the iron informs you if the temperature
of the soleplate is too high in comparison with
the setting chosen on the temperature
adjustment control (H).
Each time you appreciably reduce the
temperature adjustment control (H), the
"Thermo Sensor" indicator (J) comes on to
warn you that the soleplate is too hot and that
you risk scorching or damaging the fabric.
- Wait for the indicator (J) to go out before
continuing the ironing.
Comment: To cool down the soleplate more
quickly, iron directly onto the ironing board, in
steam position.

Maintenance

. Self-cleaning (approx. once a month):
To cut down on the formation of limescale,
Moulinex has built a self-cleaning system into
the iron, which we advise you to use at regular
intervals. Follow these steps:
Iron is cold and unplugged;
- Place the steam control (G) to
- Fill the tank (K) and set the temperature
adjustment control (H) to MAX.
16
.
.