Inhaltsverzeichnis
Werbung
Installing the glass profile
11, details 1-2-3-4) After having removed the glazing
(
bead, install the glass panel by inserting it into the metal dowels,
ensuring that it is flush with the walls.
NOTE: these dowels are adjustable so that any positioning errors
can be corrected.
11) Attach the glass profile:
(
- (detail 5) to the metal dowels,
NOTE: these dowels are adjustable so that any positioning errors
can be corrected.
- (detail 6) to the side walls.
Installing the roof frame
12) Remove the roof frame and remove the glazing beads.
(
SAUNA + HAMMAM MODELS:
Also remove the glass door profile (A1), from the sauna or
hammam frame, where the sensor (S) is present; take care when
handling the relative cable.
IN THE INSTANCE WHERE A SHOWER IS PRESENT:
12a) Remove the respective roof frame (remove the
(
protective film) and the plastic edge protectors.
Place a line of silicone on each of the plastic edge protectors
and position them as indicated, so that they are flush with the
frame edge.
13) Install the roof frame so that:
(
- (detail 1) the wood dowels on the wall are inserted into the
frame.
- (detail 2) the metal dowels are inserted into the glass profile,
- (detail 3) the metal dowels are inserted into the vertical wall
profile.
NOTE: these dowels are adjustable so that any positioning errors
can be corrected.
Subsequently, use a rubber mallet if necessary.
13) Attach the roof frame:
(
- (detail 4) to the glass profile,
- (detail 4) to the vertical wall profile,
Installing fixed glass panels
ATTENTION: in order to move the glass, use ONLY a
suitable suction lifter; the size should be suited to the
weight of the actual glass (75 kg). You must also use
suitable protective gloves.
14, details 1-2) Place a small amount of silicone on the
(
plastic spacers and position them in pairs, as indicated:
- on the base frame,
- on the vertical wall profile,
- on the glass profile,
- on the roof frame.
The spacers should be positioned against the wall profiles (part. 2).
NOTE: (detail 1) the thickness of spacers varies: any glass perpen-
dicularity errors can therefore be corrected, for example, by placing
one spacer higher than the other.
MODELS WITH SCREEN-PRINTED GLAZING:
This glass, which features near transparent areas, must
be installed according to a specified order. Therefore,
refer to the drawings attached in order to identify the
correct assemble sequence.
NOTE: the screen-printed glass side must face inwards.
SAUNA + HAMMAM MODELS:
CAUTION: the spacers must be placed on frames (base
and ceiling) of both modules and on the glass profile
of only the hammam module (see also
15, details 1-2) After having measured the length, cut
(
sections from the sealant roll which must be applied to the:
- bottom glazing bead (f-i)
- vertical glazing bead (f-i)
- top glazing bead (f-i)
NOTE: it is recommended to cut approx. 5 cm more of the sealant
than the nominal length and then remove any remaining length
once assembly is complete.
15, details 3-4) Position the small glass panel on the plas-
(
tic spacers and allow it to run so that it rests against the spacers
on the vertical profile.
15, detail 5) Check the spirit level of the roof panel (to correct
(
any perpendicularity errors, use spacers with a different thickness).
15, detail 6) Install the glazing beads
(
SAUNA + HAMMAM MODELS
Proceed to the Chapter "Installing the wood divider".
16, details 1-2) After having measured the length, cut some
(
sections from the sealant roll which must be applied to the:
- bottom glazing bead (f-i)
- vertical glazing bead (f-v)
- top glazing bead (f-s)
NOTE: it is recommended to cut approx. 5 cm more of the sealant
than the nominal length and then remove any remaining length
once assembly is complete.
16, details 3-4) Position the large glass panel on the plas-
(
tic spacers and allow it to run so that it rests against the spacers
on the vertical profile.
16, detail 5) Check the spirit level of the roof panel (to correct
(
any perpendicularity errors, use spacers with a different thickness).
16, detail 6) Install the glazing bead (even on doors, present
(
on base and ceiling frames, if removed during their installation).
SAUNA + SHOWER/HAMMAM + SHOWER MODELS:
16a, detail 1) Remove the upper glass frame and then
(
remove the glazing bead.
23
17).
Werbung
Inhaltsverzeichnis
