Herunterladen Inhalt Inhalt Diese Seite drucken

Jacuzzi sasha Serie Montageanweisung Seite 20

Inhaltsverzeichnis

Werbung

PLEASE READ THESE INSTRUCTIONS THOROUGH-
LY BEFORE PROCEEDING WITH INSTALLATION
Info
Before proceeding with installation, check that all prepara-
tory work has been completed; for details, please see the
relative pre-installation instructions.
Please refer to the "package identification" outlines, which feature
at the beginning of this present manual to view the contents of
each box/package and to allow for advanced preparation of what
you will require at the installation stage described.
GIVEN THE CONSIDERABLE WEIGHT OF SOME PARTS,
AND IN ORDER TO ENSURE CORRECT INSTALLATION,
SASHA MUST BE INSTALLED BY AT LEAST 3 PERSONS.
ATTENTION: in order to move the glass, ONLY use a
suitable suction lifter; the size should be suited to the
weight of the actual glass (75 kg). You must also use
suitable protective gloves.
NOTE: the term "module" refers to the complete sauna, hammam or
shower structure, for example the "Sasha sauna+hammam" model
includes the "sauna" module and the "hammam" module.
Installing the base (frame and tank)
1, detail1) Remove the sauna or hammam frame and
(
then remove the glazing beads.
SAUNA + HAMMAM MODELS:
Also remove the glass door (A), from either the sauna or the
hammam.
1, details 2-3) Screw the supports to the frame, adjusting
(
the corner supports to the specified measurement (also check
the spirit level).
NOTE: do not throw away the foam rubber bushings included in the
bag containing the supports! You will need them to seal the light
cable outlet holes (see the Chapter "Installing the side walls").
1, detail 4) Position the frame according to the indicated
(
measurements (in the instance of a wall mounted installation,
please also refer to the installation angle or the supporting wall).
Lower the other supports so that they rest completely on the
ground (if necessary, use shims).
NOTE: with the supports fully screwed in (example measurement:
95 mm), the cornice (see the. "Accessories" chapter) will come out
approximately 5 mm from the ground; with the supports "screwed
in" to the maximum (example measurement: 100 mm), the cornice
will come out approximately 10 mm.
IN THE INSTANCE WHERE OTHER MODULES ARE PRESENT:
2, details 1-2) Position the respective base frame so that
(
it is resting against the adjacent frame, adjusting its height so
that they are both at the same height.
2, detail 3) Attach the frames together (to facilitate the opera-
(
tion, keep the frames upright, by resting them on the wall for example).
SAUNA + SHOWER/HAMMAM + SHOWER MODELS:
2a, detail 1) Remove the lower glass frame and then re-
(
move the glazing bead.
2a, details 2-3) Screw the supports to the frame and po-
(
sition it so that it rests flush with the shower frame, adjusting the
height so that it is at the same height (check to ensure that the
supports are resting completely on the ground).
2a, detail 4) Attach the frame to the shower frame.
(
2, detail 4) Position the support plates as indicated and
(
attach them to the cross bars.
3, details 1-2) Arrange the drains in their housings in the
(
ground in such a way, so that, once the tanks are rested on top,
they will align with the holes on the actual tanks themselves.
Then, connect the drains amongst themselves and to the drain-
age system (D= shower; H= hammam).
NOTE: in the case of the hammam, the drain with rubber hose con-
nection (P) must be positioned on the left, as indicated.
4, details 1-2) in the case of the hammam, remove the
(
boiler drainage pipe and connect it to the drain with rubber
hose connection (P) (do not leave the hose under the frame but
ensure it is on the external side of the frame).
4, details 3-4-5) Position the metal tanks on the respec-
(
tive frames, caulk the indicated areas with a silicone sealant,
avoiding the drain ring nuts - cover them with their respective
covers.
4, detail 6) Place a line of silicone sealant between the
(
tanks and the frames, along the entire perimeter so that the
space is sealed. You must achieve a continuous, even seam.
4, detail 7) Assemble the equipotential terminals, screw
(
them to the shower and/or hammam base frames and connect
to the building's equipotential circuit; connect the yellow-green
cables supplied to the terminals (these cables will then be con-
nected to the faston connectors on the mixer systems).
Installing the base wall(s)
SAUNA WALLS:
5S, details 1-2) In the instance where an automatic water
- (
filling device (SC) is installed, connect the supply pipe to the wall
connection and allow it to pass through the hole at the wall base.
5S, detail 3) In the instance where a cable radio system is
- (
present, connect it to the electrical box, as indicated.
NOTE: if, on the other hand, an audio kit (optional) is present, refer
to the audio kit documentation.
20

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis