Inhaltsverzeichnis
Werbung
SAUNA+HAMMAM/SAUNA+SHOWER+HAMMAM MODELS:
The audio system (cable radio system or optional audio kit) can
be connected/installed to the "sauna" or "hammam" module.
5S, detail 4) Where present, connect the building alarm
- (
system to the indicated terminals.
NOTE: the terminals to which you must connect, are normally-open (NO)
contacts powered by a relay, which can be powered to both 220/240 V
and low voltage, but with maximum power absorption equal to 2 A.
5S, detail 5) Unroll the temperature sensor (SO) cable and
- (
allow it to pass through the grooves (the highest ones) located
at the wall end.
5S, detail 5) Unwind the display (1) cable and allow it to
- (
pass via these same grooves.
5S, detail 6) Thread the bench light cable (6) through the
- (
lower grooves and route it towards the outside.
5S, detail 7); Install the isolating multi-pole switch (with
- (
the cable already connected to the appliance's junction box) in
an area that complies with the safety regulations as specified by
current legislation in force.
The "sauna's" power supply will be connected to this switch.
NOTE: in the instance of a single-phase power supply
(220/240 V ~), you must suitably connect the terminals rela-
tive to the phases, as indicated.
5S, detail 8) Make sure, that with the sauna module, the con-
- (
tacts indicated are NOT connected to each other, as displayed.
5S, detail 9) Centring the wall on the base frame, install it
- (
in such a way so that the wood dowel is inserted into the frame.
Subsequently, use a rubber mallet if necessary.
SAUNA + HAMMAM MODELS:
ATTENTION: before proceeding with installation of
the hammam wall, connect and install the heater
(see Chapter on "Installing the heater").
HAMMAM WALLS:
5H, detail 1) In the instance where a cable radio system is
- (
present, connect it to the electrical box, as indicated.
NOTE: if, on the other hand, an audio kit (optional) is present, re-
fer to the audio kit documentation.
SAUNA+HAMMAM/SAUNA+SHOWER+HAMMAM MODELS:
The audio system (cable radio system or optional audio kit) can
be connected/installed to the "sauna" or "hammam" module.
5H, detail 2) Where present, connect the building alarm
- (
system to the indicated terminals. NOTE: the terminals to which
you must connect, are normally-open (NO) contacts powered by a
relay, which can be powered to both 220/240 V and low voltage, but
with maximum power absorption equal to 2 A.
5H, detail 3) Unroll the temperature sensor (SO) cable and
- (
allow it to pass through the grooves (the highest ones) located
at the wall end.
5H, detail 3) Unwind the display (1) cable and allow it to
- (
pass via these same grooves.
5H, detail 4) Thread the bench light cable (6) through the
- (
lower grooves and route it towards the outside.
5H, detail 5) Connect the power supply to the junction box
- (
(CP) as follows:
- 220/240V ~
(steam generator power: 4.6 kW)
Connect the power supply as indicated, additionally connect-
ing the jumper cables to the indicated terminals.
- 220/240V ~
(steam generator power: 6 kW)
Connect the power supply as indicated, additionally connect-
ing the jumper cables to the indicated terminals.
- 380/415V - 2N ~
(steam generator power: 4.6 kW)
Use two phases (in addition to neutral) and connect the pow-
er supply to the indicated terminals.
- 380/415V - 3N ~
(steam generator power: 6 kW)
Use 3 phases (in addition to neutral) and connect the power
supply to the indicated terminals.
5H, detail 6) Make sure, that with the hammam module,
- (
the contacts indicated ARE connected to each other, as dis-
played.
INSTALLATION OF REMOTE CONTROL SYSTEM
(WHERE PRESENT)
Where present, carry out installation of the equipment
by consulting the documentation that comes supplied with
the equipment itself; in the case of "Sauna+Hammam" or
"Sauna+Shower+Hammam" models, the control system may be
installed either to the sauna or hammam module.
SAUNA + HAMMAM MODELS:
6) ATTENTION: before proceeding with installa-
(
tion of the hammam wall, connect the light cables
together (coming from the two electrical boxes) us-
ing the supplied cable (C).
6H, detail 1) Draw the wall to the wall connections and
- (
connect these to the mixer system using the flexible pipes sup-
plied.
6H, detail 2) Connect the yellow-green cable to the faston
- (
connector on the mixer system.
6H, detail 3) Connect the pipe coming from the drain with
- (
rubber hose connection to the coupler of the steam generator's
drainage system.
21
Werbung
Inhaltsverzeichnis
