Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Safety, performance, and dependability have been given
top priority in the design of your project light.
INTENDED USE
The project light is designed for general illumination of most
work area spaces.
PROJECT LIGHT SAFETY WARNINGS
■
Know the product. Read user's manual carefully.
Learn its applications and limitations as well as the
specific potential hazards related to the product.
■
Use only with recommended battery pack and
charger. Any attempt to use another battery pack
will cause damage to the product and could possibly
explode, cause a fire, or personal injury.
■
Do not disassemble the product.
■
Do not permit children to use the product. It is not
a toy.
■
The product is not designed to operate in wet or
damp conditions.
■
The product is non-dimmable; do not connect with
any dimmers.
■
If wrapped or in contact with fabrics, the project
light lens can produce sufficient heat to melt some
fabrics. To avoid serious personal injury, never allow
the project light lens to come in contact with anything.
■
Do not direct the light beam at persons or animals
and do not stare into the light beam yourself (not
even from a distance). Staring into the light beam may
result in serious injury or vision loss.
■
Do not place the product or battery pack near fire or
heat. This will reduce the risk of explosion and possible
injury.
■
Do not store the product in a damp or wet location,
or in a location where the temperature may reach
or exceed 40°C (104°F). For example, inside sheds,
vehicles, or metal buildings in the summer.
■
Check damaged parts. Before further use of the
product, a part that is damaged should be carefully
checked to determine that it will operate properly and
perform its intended function. Do not use the product if
it does not function properly.
■
Have the product repaired by a qualified person.
The product is in accordance with the relevant safety
requirements. Repairs should only be carried out by
qualified person using original spare parts, otherwise
this may result in considerable danger to the user.
■
The light source contained in this luminaire shall only be
replaced by the manufacturer or his service agent or a
similar qualified person.
BATTERY AND CHARGER SAFETY WARNINGS
■
Connect and disconnect the battery pack properly.
●
To install battery pack:
–
Place the battery pack on the product.
–
Make sure the latches on each side of the
battery pack snap into place and the battery
pack is secured on the product before beginning
operation.
●
To remove battery pack:
–
Depress the latches on the side of the battery
pack.
–
Remove the battery pack from the product.
■
Remove battery when the product is not in use and
before servicing.
■
Do not place batteries near fire or heat. They may
explode.
■
Rechargeable batteries are to be removed from the
product before being charged.
■
Different types of batteries or new and used batteries
are not to be mixed.
■
Batteries are to be inserted with the correct polarity.
■
Exhausted batteries are to be removed from the product
and safely disposed of.
■
If the product is to be stored unused for a long period,
the batteries should be removed.
■
The supply terminals are not to be short-circuited.
■
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in contact
with skin, wash at least 10 minutes then seek immediate
medical attention.
■
Batteries vent hydrogen gas and can explode in the
presence of a source of ignition, such as a pilot light.
To reduce the risk of serious personal in jury, never use
any cordless product in the presence of an open flame.
An exploded battery can propel debris and chemicals. If
exposed, flush with water immediately.
■
Electric shock could occur if the battery is charged
outdoors or on wet surfaces.
■
Do not expose charger to wet or damp conditions.
■
Use of an attachment not recommended or sold by the
battery charger manufacturer may result in a risk of fire,
electric shock, or injuries to person.
■
To reduce risk of damage to charger body and cord, pull
by charger plug rather than cord when disconnecting
charger.
■
Make sure cord is located so that it will not be stepped
on, tripped over, or otherwise subjected to damage and
stress.
■
An extension cord should not be used unless absolutely
necessary. Use of improper extension cord could result
in a risk of fire and electric shock. If extension cord must
be used, make sure:
a) That pins on plug of extension cord are the same
number, size and shape as those of plug on
charger.
b) That extension cord is properly wired and in good
electrical condition.
■
Do not operate charger with a damaged cord or plug. If
damaged, have it replaced immediately by a qualified
serviceman.
■
Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way; take
it to a qualified serviceman.
■
Do not disassemble charger; take it to a qualified
serviceman when service or repair is required. Incorrect
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
EL
English |
1
Werbung
Inhaltsverzeichnis
