Functional Description - Makita DFS452 Bedienungsanleitung

FUNCTIONAL
DESCRIPTION
CAUTION:
• Always be sure that the tool is switched off and
the battery cartridge is removed before adjust-
ing or checking function on the tool.
Installing or removing battery
cartridge
► Fig.1: 1. Red indicator 2. Button 3. Battery cartridge
CAUTION:
• Always switch off the tool before installing or
removing of the battery cartridge.
• Hold the tool and the battery cartridge firmly
when installing or removing battery car-
tridge. Failure to hold the tool and the battery
cartridge firmly may cause them to slip off your
hands and result in damage to the tool and
battery cartridge and a personal injury.
To remove the battery cartridge, slide it from the tool
while sliding the button on the front of the cartridge.
To install the battery cartridge, align the tongue on the
battery cartridge with the groove in the housing and slip
it into place. Insert it all the way until it locks in place
with a little click. If you can see the red indicator on the
upper side of the button, it is not locked completely.
CAUTION:
• Always install the battery cartridge fully until the
red indicator cannot be seen. If not, it may acci-
dentally fall out of the tool, causing injury to you
or someone around you.
• Do not install the battery cartridge forcibly. If the
cartridge does not slide in easily, it is not being
inserted correctly.
Switch action
CAUTION:
• Before inserting the battery cartridge into the
tool, always check to see that the switch trigger
actuates properly and returns to the "OFF"
position when released.
• Switch can be locked in "ON" position for ease
of operator comfort during extended use. Apply
caution when locking tool in "ON" position and
maintain firm grasp on tool.
► Fig.2: 1. Switch trigger 2. Lock button
To start the tool, simply pull the switch trigger. Tool
speed is increased by increasing pressure on the switch
trigger. Release the switch trigger to stop.
For continuous operation, pull the switch trigger, push in
the lock button and then release the trigger.
To stop the tool from the locked position, pull the switch
trigger fully, and then release it.
NOTE:
• Even with the switch on and motor running,
the bit does not rotate. Push the tool forward to
engage the clutch.
• The tool automatically stops if the motor keeps
rotating for about 6 minutes.
Push drive mode
► Fig.3: 1. Button 2. Mode indicator
This tool has push drive mode. In this mode, the tool
cuts off power to the motor to save the battery power
at idle.
To select push drive mode, pull the trigger slightly, then
release it and quickly press the button. The mode indi-
cator will then light up.
Once push drive is activated, pull the switch trigger and
then push the lock button. Apply pressure to the bit and
the motor will start rotating. Further pressure engages
the clutch and the bit will start rotating. In push drive
mode, the motor and the driver bit will only rotate by
applying pressure.
NOTE:
• If the tool does not run for about 8 hours in push
drive mode with the trigger locked on, tool is
shutdown. In such a case, release and pull the
trigger again for restarting.
Lighting up the lamp
► Fig.4: 1. Lamp 2. Button
To turn on the lamp, slightly pull the switch trigger,
release it and then press the button for a few seconds.
The lamp turns on. The lamp goes out approximately 10
seconds after releasing the switch trigger. To turn on the
lamp again, slightly pull the switch trigger again.
To keep turning off the light, slightly pull the switch
trigger and release it. Then press the button a few
seconds.
In push drive mode with the switch trigger locked, the
lamp goes out approximately one minute after the motor
stops.
NOTE:
• While pulling the switch trigger, the lamp mode
cannot be changed.
• For approximately 10 seconds after releas-
ing the switch trigger, the lamp mode can be
changed.
• Use a dry cloth to wipe the dirt off the lens of
lamp. Be careful not to scratch the lens of lamp,
or it may lower the illumination.
6 ENGLISH