Shure ULX-D Bedienungsanleitung Seite 14

ULXD Specifications
Working Range
100 m (330 ft)
Note: Actual range depends on RF signal absorption, reflection and interference.
Audio Frequency Response
ULXD1 20 – 20 kHz (±1 dB)
ULXD2 Note: Dependent on microphone type
Audio Dynamic Range
System Gain @ +10
>120 dB, A-weighted, typical
System Audio Polarity
Positive pressure on microphone diaphragm produces positive voltage on pin 2 (with
respect to pin 3 of XLR output) and the tip of the 6.35 mm (1/4-inch) output.
Operating Temperature Range
-18°C (0°F) to 50°C (122°F)
Note: Battery characteristics may limit this range.
Housing
ULXD4D/ULXD4Q
Steel; Extruded aluminum Cast aluminum
ULXD4 Power Requirements
ULXD4D 100 to 240 V AC, 50-60 Hz, 0.26 A max.
ULXD4Q 100 to 240 V AC, 50-60 Hz, 0.32 Amax.
Battery Type
Shure SB900 Rechargeable Li-Ion or LR6 AA batteries 1.5 V
Battery Runtime
@ 10 mW
Shure SB900 alkaline
>11 hours 11 hours
Certifications
ULXD1, ULXD2, ULXD4D, ULXD4Q
This product meets the Essential Requirements of all relevant European directives and is
eligible for CE marking.
ULXD1, ULXD2
Certified under FCC Part 74.
Certified by IC in Canada under RSS-123 and RSS-102.
IC: 616A-ULXD1 G50, 616A-ULXD1 H50, 616A-ULXD1 J50, 616A-ULXD1 L50;
616A-ULXD2 G50, 616A-ULXD2 H50, 616A-ULXD2 J50, 616A-ULXD2 L50.
FCC: DD4ULXD1G50, DD4ULXD1H50, DD4ULXD1J50, DD4ULXD1L50;
DD4ULXD2G50, DD4ULXD2H50, DD4ULXD2J50, DD4ULXD2L50.
IC: 616A-ULXD1X52, 616A-ULXD2X52
FCC: DD4ULXD1X52, DD4ULXD2X52
ULXD4D, ULXD4Q
Approved under the Declaration of Conformity (DoC) provision of FCC Part 15.
Certified by IC in Canada under RSS-210.
IC: 616A-ULXD4D G50, 616A-ULXD4D J50, 616A-ULXD4D L50; 616A-ULXD4Q G50,
616A-ULXD4Q J50, 616A-ULXD4Q L50.
Conforms to electrical safety requirements based on IEC 60065.
14
ULXD1 ULXD2
Machined aluminum
Frequency Range and Transmitter Output
Frequency
Band
Range ( MHz)
G50 470 to 534
G51 470 to 534
G52 479 to 534
H50 534 to 598
H51 534 to 598
H52 534 to 565
J50 572 to 636
K51 606 to 670
L50 632 to 696
L51 632 to 696
P51 710 to 782
R51 800 to 810
JB (Tx only) 806 to 810
770 to 810
AB (Rx and Tx)
Q51 794 to 806
X50 925 to 932
X51 925 to 937.5
902 to 928 (All
X52 America's except
Brazil)
902 to 907.500,
X53
915 to 928 (Brazil)
915 to 928
X54
(Australia)
The CE Declaration of Conformity can be obtained from: www.shure.com/europe/
compliance
Authorized European representative:
Shure Europe GmbH
Headquarters Europe, Middle East & Africa
Department: EMEA Approval
Jakob-Dieffenbacher-Str. 12
75031 Eppingen, Germany
Phone: 49-7262-92 49 0
Fax: 49-7262-92 49 11 4
Email: info@shure.de
Australia Warning for Wireless
This device operates under an ACMA class licence and must comply with all the
conditions of that licence including operating frequencies. Before 31 December 2014, this
device will comply if it is operated in the 520-820 MHz frequency band. WARNING: After
31 December 2014, in order to comply, this device must not be operated in the 694-820
MHz band.
Power
Power ( mW RMS)
(Lo/Nm/Hi)
1/10/20
1/10/20
1/10
1/10/20
1/10/20
1/10
1/10/20
1/10
1/10/20
1/10/20
1/10/20
1/10/20
1/10
'A' Band (770-805): 1/10/20
'B' Band (806-809): 1/10
1/10/20
1/10
10
0.25/10/20
0.25/10/20
0.25/10/20