Inhaltsverzeichnis
Werbung
GB
-Check every pool screws, the corrosion points possible and check the liner is clean before filling the pool.
-The pool water level has always to be hold in a minimum of 20 cm from the pool superior edge. FILL IT UP TO THE BEGINNING OF THE INFLATABLE CHAMBER.
Do not leave the pool without any water.
Attention: the appearance of drops of water on the sides of the swimming pool is a natural effect of moisture exuding from the material with which the pool is manufactured. After
a few weeks it disappears. These drops slip down the outside to the bottom, accentuating the impression of damp which forms beneath the pool through condensation. This is
not, in either case, a defect of the product.
-Clean regularly the P.V.C liner and the water level mark with non-abrasive products. If you do by accident a small hole in the liner, you can repair it thanks to our rubber patches
AR202 and V12.
-You have to use the ladder exclusively to go in or to go out of the pool. (Remove it after use)
-The isothermic covers (for the summer) protect your pool from insects, dust, leaves, ... and avoid to loose the water temperature. Do always set it in order the bubbles are in
contact with the water.
Chimical measures : Please read carefully the chemical product manufacturer instructions. WARNING: Keep chemical products in a clean, dry and out of children place. Important :
Every products used have to be compatible with the P .V.C liner.
-First filling : Analyse the water pH and chlorine (Cl) and adjust them to the optimal levels : pH : 7,2 – 7,6 ; Chlorine : 0.5 – 2 ppm.
-Chlorine treatments : Consist in increasing the chlorine level until approximatively 20ppm to eliminate germs and seaweeds. This process has to be done only when the pool
water comes from rivers or ponds, ... or if it stayed a long time without any treatments.
-Checking : Check at least once a week the chlorine levels (Use a chlorine and pH analyser). In the same way, we advise to add an algicid to prevent seaweeds appearance.
-Warning : Never have a swim before the chlorine level stabilization. Make sure the pool water level is correct.
Do always use a floating dispenser for the chemical product (tablets) dissolution. The chemical product measuring out has to be done in accordance with : Your pool water
volume, the bathe frequency, the climatic conditions, the water temperature and the location. Do always move the water and wait for the chemical product dissolution before
adding another one. Wait approximatively 12 hours between any pH, chlorine or algicid adjustment using the filter system.
-Mechanical measures :Check the filter, the skimmer, the valves and the pipes are well connected to the pool. Switch on the filter system once a day in to insure a complete
water volume renewal and never do it when somebody is in the pool (see filter manual). Do consider high water temperature will involved more time for the filtering. Theoretic
filtering time = Water volume / Filter system discharge (generally 8h/day with water temperature of 21°C), (Ideal : 2h in the morning – 4h around midday – 2h in the afternoon).
PLEASE RESPECT THE CONTINUOUS WORKING PERIOD INDICATED IN THE FILTER MANUALS
-Bottom cleaner for exhaustion (manual or automatic) : Only for pools with skimmer. Connect an hose extremity to the brush head and immerse it into the water to make
it fill in. Connect the other pipe extremity to the exhaustion adapter (TA) and place it above the skimmer basket. Switch on the filter in the FILTER position and begin to clean
the bottom.
-Bottom cleaner Ventury style : Connect a garden hose to the bottom cleaner join and introduce it into the pool. Open the tap until a normal pressure to make the water
flow out against the bottom of the pool, producing in that way an ascendant stream which leave the dirt into the filter (bag) which is adjust on the bottom cleaner.
PROBLEMS
Cloudy water
Green water
Brown water
Skin and eyes Irritation. Bad smells
WATER CONTROL IMPORTANCE : It's important to do this controls to insure a water quality and the bather security, to prevent infection, intoxication problems,... due
to a bad state of water.
WINTER:
1°- Emptying: Introduce the end of a garden hose into the drain port of the pool and take the other end to the place chosen for water runaway. If the water contains chlorine
or bleach, do not use it for watering the garden.
2°-Clean every pool constituents with a sponge and a soap product with a neutral pH. Dry them and tidy them away in a dry and clean place. That's normal that after having
installed and dismounted the pool several times, the P.V.C liner dilate and loose its elasticity.
CAUSES
Filters deficiencyPH too high
Organic residues excess
Seaweeds and mildew formation
Iron or manganese presence
Unbalanced pH. Organic residues excess
SOLUTIONS
Put back some clean water in the pool, add into the dispenser a
flocculant in tablets. Realise a chlorine treatment
Brush carefully the bottom and the steel walls of the pool
Analyse the pH and adjust it Realise a chlorine treatment
Analyse the pH and adjust it Realise a chlorine treatment
Add an algicid and a flocculant
Replace the pool water
17
Werbung
Inhaltsverzeichnis
