Safety Notes; Technical Data - Grohe 36 325 Bedienungsanleitung

GB
Application
Can be used in conjunction with:
• Pressurised storage heaters
• Thermally-controlled instantaneous heaters
• Hydraulically-controlled instantaneous heaters
Operation with unpressurised storage heaters (open water
heaters) is not possible.

Safety notes

• Installation is only possible in frost-free rooms.
• The switched-mode power supply is only suitable for
indoor use.
• In the case of damage to the external connection cable of the
power supply unit, it must be replaced by the manufacturer
or the manufacturer's customer service department or an
equally qualified person, in order to prevent a hazard.
• The switched-mode power supply connector must not be
directly or indirectly sprayed with water for cleaning purposes.
• The voltage supply must be separately switchable.
• Use only genuine replacement parts and accessories.
The use of other parts will result in voiding of the warranty
and the CE identification.
• The mixer spindle is mechanical and therefore not controlled
electronically.

Technical data

• Flow pressure:
- min.
- recommended
• Operating pressure:
• Test pressure:
If static pressures exceed 0.5 MPa, a pressure-reducing valve
must be installed.
Avoid major pressure differences between hot and cold water
supply.
• Flow rate at 0.3 MPa flow pressure:
• Hot water supply temperature:
Recommended (energy economy):
Fitting with switched-mode power supply (36 325):
• Voltage supply: 100-240 V AC 50-60 Hz/6.75 V DC
• Power consumption:
Fitting with battery (36 327, 36 330, 36 331):
• Voltage supply: 6V lithium battery type CR-P2
• Automatic safety shut-off:
(5 - 420 s adjustable)
• Run-on time (0 - 10 s adjustable):
• Reception range according to Kodak Gray Card,
grey side, 8x10", landscape (factory setting): approx. 13cm
• Type of fitting protection:
• Water connection
Electrical test data
• Software class
• Contamination class
• Rated surge voltage
• Temperature of ball impact test
The test for electromagnetic compatibility (interference emission
test) was performed at the rated voltage and rated current.
5
General functions
• Thermal disinfection:
• Remaining battery capacity:
Programme 1 functions (factory setting)
• Cleaning mode:
• Automatic flushing:
• Thermal disinfection time:
Further pre-set programmes can be selected via the sensor
system.
Special accessories
Further settings and special functions are available via the
infrared remote control (prod. no. 36 206).
Approval and conformity
This product conforms to the requirements of the
relevant EU directives.
The conformity declarations can be obtained from the following
address:
GROHE Deutschland Vertriebs GmbH
Zur Porta 9
D-32457 Porta Westfalica
Installation
Flush pipes thoroughly before and after installation
0.05 MPa
(observe EN 806).
0.1 - 0.5 MPa
max. 1 MPa
Fitting
1.6 MPa
Refer to the dimensional drawings on fold-out page I and fold
out page II, Fig. [1].
Fasten fitting to wash basin, see Figs. [2] to [4].
Prod. no. 36 331:
approx. 6 l/min
Lift rod (A) must be inserted into the mixer body during
max. 70 °C
installation, see Fig. [2].
60 °C
Connection
The cold water supply must be connected on the right,
hot water supply on the left.
2.4 W
Insert filter (B) and connect the hoses to the service valves,
see Fig. [5].
Connecting the voltage supply
60 s
Prod. no. 36 325:
1. Connect plug-in connector between electronics cable (C)
1 s
and power supply unit (D), see Fig. [6].
2. Connect voltage supply via power supply unit (D).
IP 59K Prod. no. 36 327, 36 330, 36 331:
cold - right
1. Secure bracket (E1) using screws and plugs, see Fig. [7].
hot - left
2. Insert battery (E2) in battery housing (E4) and fit lid (E3).
Observe correct polarity.
3. Connect plug-in connector between electronics cable (C)
A
and battery housing (E), see Fig. [8].
2
4. Engage battery housing (E) in bracket (E1).
2500 V
100 °C
Open hot and cold water supply and check that
connections are watertight.
activatable
readable
activatable
deactivated
3.5 min