Safety Notes; Technical Data; Operation; Making Settings - Grohe Tectron 37 324 Montageanleitung

GB

Safety notes

• Installation is only possible in frost-free rooms.
• Use only genuine replacement parts and accessories.
The use of other parts will result in voiding of the warranty
and the CE identification.

Technical data

• Flow pressure:
- min.
- recommended
• Operating pressure:
• Test pressure:
• Temperature:
• Voltage supply: 6V lithium battery type CR-P2
• Flow volume (1 - 7 l adjustable):
• Minimum delay (2 - 10 s, adjustable):
• Type of protection:
• Pipe:
• Integrated isolating valve
General functions
• Remaining battery capacity:
Programme 1 functions (factory setting)
• Cleaning mode:
• Automatic flushing (24h):
• Detection zone according to Kodak Gray Card,
grey side, 8x10", landscape:
• Pre-flushing:
• Intermediate flushing:
Further pre-set programmes can be selected via the sensor
system, see the programme table on page 6.
Special accessories
Further settings and special functions are available via
the infrared remote control (Prod. no. 36 206).
Approval and conformity
This product conforms to the requirements of the
relevant EU directives.
The conformity declarations can be obtained from the following
address:
GROHE Deutschland Vertriebs GmbH
Zur Porta 9
D-32457 Porta Westfalica
Final installation
, see fold-out page II, Figs. [1] - [7]

Operation

The infrared electronics emits invisible pulsed light. If this light
is reflected by a user for a minimum of 5 seconds (minimum
delay) and is then received again by the electronics, the bowl
is flushed after the user moves away.
The detection zone is dependent upon the reflective properties
of the object.
Activating cleaning mode
• Only possible when temporary shutoff is activated.
• The detection zone must kept clear.
0.05 MPa
0.1 - 0.5 MPa 1. Hold finger against the lower area of the sensor system,
max. 1 MPa
1.6 MPa
max. 45 °C
█████████████████████ ██ ██ ██ ██ ██
2 l
2. Remove finger from the sensor system while
5 s
IP 56
Cleaning mode is active for 3 minutes. The indicator lamp
DN 15
Terminating cleaning mode prematurely
readable
1. Hold finger against the lower area of the sensor system,
activatable
activated
█████████████████████____
45cm 2. Remove finger from the sensor system while
deactivated
activated
Signalling the remaining battery capacity
1. Hold finger against the lower area of the sensor system,
█████████████████████ ██ ██ ██ ██ ██ ██ ██ ▌▌▌▌▌
2. Remove finger from the sensor system while
The remaining battery capacity is signalled by the number
██ ██ ██ ██
██ ██ ██
██ ██
██

Making settings

Setting mode
Setting mode has the following functions:
- Changing the flow volume
- Querying and changing the programme
- Checking the detection zone
The indicator lamp in the sensor system illuminates in setting
mode when the detection zone of the fitting is reached by an
approaching user. Flushing is immediately triggered when the
detection zone is exited again. The minimum delay is not
available in setting mode.
see Fig. [8].
Indicator lamp signals:
██ ██ ██
is displayed.
flashes during this time.
see Fig. [8].
Indicator lamp signals:
displayed.
Cleaning mode is terminated.
see Fig. [8].
Indicator lamp signals:
is displayed.
of flashing signals:
Remaining battery capacity > 60%
Remaining battery capacity > 40%
Remaining battery capacity > 20%
Remaining battery capacity < 20%
is
____
▌▌▌▌
4