Specifications; Functional Description - Makita 9741 Betriebsanleitung

ENGLISH
(Original instructions)
1 Wing nut
2 Front roller
3 Switch trigger
4 Lock button
5 Spindle
6 Wheel

SPECIFICATIONS

Model
Wheel size (Diameter x Width) ................. 100 x 120 mm
–1
No load speed (min ) ............................................ 3,500
Dimensions (L x W x H) .................. 310 x 185 x 182 mm
Net weight .............................................................. 4.2 kg
.......................................................
Safety class
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2014
Intended use
The tool is intended for removing paint with slit paper
wheel and fine metal cleaning with wire brush wheel.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
General power tool safety warnings
WARNING: Read all safety warnings, instructions,
illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future refer-
ence.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
WHEEL SANDER SAFETY WARNINGS
1. Hold the power tool by insulated gripping sur-
faces, because the wheel may contact its own
cord. Cutting a "live" wire may make exposed metal
parts of the power tool "live" and could give the oper-
ator an electric shock.
2. Always use safety glasses or goggles. Ordinary
eye or sun glasses are NOT safety glasses.
3. Inspect for and remove foreign matter such as
nails, screws, etc. from the workpiece surface
before operation.
4. Secure the workpiece firmly.
5. Do not wear gloves during operation.
6. Hold the tool firmly with both hands.
7. Keep hands away from rotating parts.
Explanation of general view
7 Output shaft
8 Hex wrench
9 Notch
10 Pin
11 Dust port
12 Cover plate
8.
9741
9.
10. Some material contains chemicals which may be
/II
11. Use of this tool to sand some products, paints
SAVE THESE INSTRUCTIONS.
ENE053-1
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
ENF002-2
tion manual may cause serious personal injury.

FUNCTIONAL DESCRIPTION

• Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the
GEA010-2
tool.
Adjusting front roller (Fig. 1)
The front roller allows you to apply uniform pressure to
the workpiece. To adjust the front roller, set the tool on a
flat surface and loosen the wing nut. Adjust the front
roller up or down until the clearance distance (D) is about
2 mm. Tighten the wing nut securely.
Switch action (Fig. 2)
• Before plugging in the tool, always check to see that
the switch trigger actuates properly and returns to the
GEB146-1
"OFF" position when released.
To start the tool, simply pull the switch trigger. Release
the switch trigger to stop.
For continuous operation, pull the switch trigger and then
push in the lock button.
To stop the tool from the locked position, pull the switch
trigger fully, then release it.
ASSEMBLY
• Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
13 Joint
14 Grip
15 Handle
16 Limit mark
17 Screwdriver
18 Brush holder cap
Do not leave the tool running. Operate the tool
only when hand-held.
Never attempt to use with the tool held upside
down in a vise, etc.
toxic. Take caution to prevent dust inhalation
and skin contact. Follow material supplier safety
data.
and wood could expose user to dust containing
hazardous substances. Use appropriate respira-
tory protection.
WARNING:
CAUTION:
CAUTION:
CAUTION:
3