Black+Decker BEH550 Bersetzung Der Ursprünglichen Anweisungen Seite 5

Labels on tool
The following pictograms are shown on the tool along with the
:
date code:
Warning! To reduce the risk of injury, the user
f
must read the instruction manual.
Wear ear protectors with Impact drills. Exposure
to noise can cause hearing loss
Electrical safety
#
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
Features
1. Variable speed switch
2. Lock on button
3. Forward/reverse switch
4. Drilling mode selector
5. Chuck
6. Chuck lock
7. Side handle
Assembly
Warning! Before assembly, make sure that the tool is
switched off and unplugged.
Fitting the side handle (fig. A)
Turn the grip counterclockwise until you can slide the side
u
handle (7) onto the front of the tool.
Rotate the side handle into the desired position.
u
Tighten the side handle by turning the grip clockwise.
u
Fitting an accessory (fig. B)
Press the chuck lock (6)
u
Open the chuck by turning the sleeve (5) counterclock-
u
wise.
Insert the bit shaft (8) into the chuck.
u
Tighten the chuck by turning the sleeve clockwise.
u
Use
Warning! Let the tool work at its own pace. Do not overload.
Warning! Before drilling into walls, floors or ceilings, check for
the location of wiring and pipes.
Switching on and off (fig. C)
To switch the tool on, press the variable speed switch (1).
u
(Original instructions)
The tool speed depends on how far you press the switch.
For continuous operation, press the lock-on button (2) and
u
release the variable speed switch. This option does not
work in reverse rotation.
To switch the tool off, release the variable speed switch.
u
To switch the tool off when in continuous operation, press
the variable speed switch once more and release it.
Selecting the direction of rotation (fig. D)
For drilling and tightening screws, use forward (clockwise)
rotation. For loosening screws or removing a jammed drill bit,
use reverse (counterclockwise) rotation.
To select forward rotation, push the forward/reverse slider
u
(3) to the left.
To select reverse rotation, push the forward/reverse slider
u
to the right.
Warning! Never change the direction of rotation while the
motor is running.
Selecting the drilling mode (fig. E)
For Impact drilling in masonry and concrete, set the
u
drilling mode selector (4) to the
For drilling in steel, wood and plastics or for screw driving
u
set the operating mode selector (4) to the
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or switch off and remove the battery from the appliance/
u
tool if the appliance/tool has a separate battery pack.
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it. Your charger does
u
not require any maintenance apart from regular cleaning.
Regularly clean the ventilation slots in your appliance/tool/
u
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
u
from the interior (when fitted).
ENGLISH
q
position.
r
position.
5