Control Panel; Cleaning And Care - Vitek VT-1769 W Die Betriebsanweisung

Draughts or other air flows may affect the air
humidity indications in the room.

CONTROL PANEL (2)

«SWITCH ON» Button (14)
You can switch the unit on and off by one pressing
of the button.
«IONIZATION» Button (15)
You can switch the ionization mode on and off by
one pressing of the button (15) «IONIZATION».
«MAX/MIN» Button (16)
Select mist release intensity by pressing
consequently the button (16) «MAX/MIN»:
«1» - low intensity,
«2»- medium intensity,
«3»- high intensity.
«HUMIDIFICATION» Button (17)
Set the desired relative humidity level in the
room. Once the desired relative humidity level is
reached, the unit will be switched off, when the
relative humidity level decreases, the unit will
switch on.
Consequently press
«HUMIDIFICATION» to set the relative humidity
level from 45% to 75% with a step 5%.
To cancel the maintenance of the relative
humidity level consequently press the button (17)
«HUMIDIFICATION» till the symbol «Co» appears
on the display (1), the unit will be operating
constantly.
«TIMER» timer on button (18)
You can set the switch off time. To do this,
consequently press or hold the button (18)
«TIMER». The timer is set in the range from 1 to
12 hours with 1 hour step.
To switch the timer off consequently press the
button (18) «TIMER» until the symbol «- - H»
appears on the display.
Low water level indication
When the water tank (8) becomes empty, the unit
will be switched off, you will hear a sound signal,
and the indicator will light up red in the right part
of the display. Switch the unit off using the button
(14) «SWITCHING ON» and unplug it, remove
the nozzle (11) and the water tank. Fill the tank
VT-1769.indd 5
with water (see the chapter «Operation»). Install
the filled tank and then the nozzle back to their
places. Switch the unit on.
Water tank illumination (5)
The illumination (5) lights up when the unit is
plugged in. The illumination allows to check the
water level in the tank (8).

CLEANING AND CARE

Warning! Always switch the unit off and
unplug it before cleaning.
Hard water causes appearance of mineral scale
in the process chamber (4) and in the water tank
(8) that leads to improper operation of the unit.
To avoid it:
– use filtered, boiled and settled water. If tap
– change water in the water tank (8) every day.
Weekly care
– Thoroughly wash the process chamber (4)
the button (17)
– To clean the sprayer add 5-10 drops of deter-
Note:
As a cleaning agent for the sprayer you can
use scale removers for electric kettles.
Do not immerse the unit body into water or
other liquids.
Cleaning of the cartridge filter (7)
– The cartridge filter (7) prevents generation
– Clean the cartridge filter after passing of
– Take the handle (9) and remove the water
– Turn over the tank, open the lid (6) with the
5
ENGLISH
water is hard, it is recommended to mix it with
distilled water in proportion 1:1. If tap water is
too hard, mix it with distilled water in propor-
tion 1:2 or use distilled water only.
and the water tank (8) with neutral detergent
solution.
gent on it and wait for 2-5 minutes. Remove
the deposit from the sprayer surface with a
brush (13).
of bacteria, softens the water and removes
unpleasant smells.
about 1000 l of water through it, and if using
hard water or a white deposit appears on the
furniture, more often.
tank (8) from the unit body. Remove the noz-
zle (11).
cartridge filter rotating it counterclockwise.
Remove the lid (6) from the cartridge filter.
05.12.2013 10:54:54