Inhaltsverzeichnis
Werbung
SETUP:
SETUP:
PRINTER OFF
PRINTER SETTINGS
PRINTER TYPE .............................KUBEVR 1 CIS
PRINTING HEAD TYPE .................SHEC T80
INTERFACE ...................................RS232
PROGRAM MEMORY TEST..........OK
DYNAMIC RAM TEST....................OK
FPGA TEST....................................OK
EEPROM TEST..............................OK
CUTTER TEST...............................OK
HEAD VOLTAGE
[ V] = 24.29
HEAD TEMPERATURE
[°C] = 30
POWER ON COUNTER
= 1843
PAPER PRINTED
[cm] = 76930
CUT COUNTER
= 5507
DATE - TIME
= 01/01/08 12:00
Printer Emulation .......................:
RS232 Baud Rate
(1)
..................:
RS232 Data Length
...............:
(1)
RS232 Parity
..........................:
(1)
RS232 Handshaking
(1)
..............:
Busy Condition
.......................:
(1)
USB Address Number
(2)
............:
Print Mode .................................:
Autofeed ....................................:
Chars / inch ...............................:
Speed / Quality
......................:
(3)
Paper Width...............................:
Paper Threshold
....................:
(7)
Notch Alignment ........................:
Notch Threshold
(4)
.....................:
Notch Distance [mm]
..............:
(4)
PaperEnd Buffer Clear ..............:
PowerFail WakeUp Mode
......:
(6)
Total Cut
.................................:
(5)
Print Density..............................:
[LF] enter Printer Setup
[LF+ON/OFF] enter Clock Setup
[ON/OFF]
skip Setup
1 Go into SETUP mode by pressing the FEED key before switch
2 The printer should print all list of the parameters:
CLICK
x
1sec.
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
ESC/POS (TM)
Notes:
115200 bps
Note
8 bits/chr
Note
None
Xon/Xoff
RxFull
0
Note
Normal
CR disabled
A=15 B=20 cpi
High Speed
82 mm
60%
Disabled
Note
80%
+20.0
Disabled
LAST PWR State
Note
Enabled
0%
Note
Note
<17>
GB
on the printer and going on to press it for a few seconds after the
printer power up.
SVELTA, ESC/POS
Printer Emulation:
: 115200, 57600, 38400, 19200
(1)
RS232 Baud Rate
4800, 2400, 1200.
: 7, 8
D
RS232 Data length
(1)
: None
D
, even, odd.
RS232 Parity
(1)
: XON/XOFF, Hardware
(1)
RS232 Handshaking
: OffLine/RXFull, RXFull
(1)
Busy condition
: 0
USB Address Number
(2)
Normal
,Reverse.
D
Print mode:
CR disabled
D
, CR enabled.
Autofeed:
A=11 B=15 cpi, A=15 B=20 cpi
Chars/Inch:
: Normal
D
(3)
Speed/Quality
: 72, 74, 76, 78, 80, 82 mm
Paper width
: 30%, 40%, 50%, 60%
Paper Threshold
(7)
Disabled
Notch alignment:
: 30%, 40%, 50%, 60%, 70%, 80%
(4)
Notch Threshold
: 00.0
Notch Distance [mm]
(4)
Disabled
PaperEnd Buffer Clear:
PowerFail WakeUp mode
Always ON.
: Disabled, Enabled
Total cut
(5)
-50%, -37%, -25%, -12%, 0
Print Density:
+50%.
The parameters marked with the symbol
: Parameter valid only on serial printer.
(1)
: This parameter is displayed only for models with USB interface; it's
(2)
used to identify univocally the USB printer by a numerical address
code, if to the PC are connected two printers that are the same
models, for example two Kube-U.
: "Current consumption" parameter is not set by the user but it depends
(3)
on the "Speed/Quality" parameter in this way:
Speed/Quality
Low Speed
Normal Speed
High Speed
: The parameter "Notch Distance" is displayed and enabled only in
(4)
case that the parameter "Notch Alignment" is enabled. The param-
eter "Notch Distance" is used to set the exact distance of the notch
entering the desired value in millimetre and in deci-millimeter.
: When this parameter is disabled, the printer always executes a partial
(5)
cut because the total cut command will be ignored; otherwise when
is enabled, the total cut command (Esc i) will be executed.
: Using this parameter, when occurs a power fail the printer can be
(6)
switched on automatically, without press On/Off key.
- "LAST PWR State": put the printer in the previous state (ON or
OFF) before a power fail;
- "Always ON": the printer always switch on automatically, after a
power fail;
- "Always OFF": the printer switch on only pressing On/Off key, after
a power fail.
: This parameter indicates the threshold value under the sensor detect
(7)
the paper.
TM D
.
D
bits/chr.
.
D
.
D
, 1, 2, 3, 4, 5, 6, 7, 8, 9.
D
.
D
, High quality, High Speed.
.
D
D
, 70%, 80%, 90%.
, Enabled.
D
D
.
D
D
, Enabled.
: LAST PWR State
, Always OFF,
D
(6)
.
D
D
,+12%, +25%, +37%,
are the default values.
D
Current consumption
Low Current
High Current
High Current
, 9600,
, 90%.
Werbung
Inhaltsverzeichnis
