Vitek VT-2509 Y Die Betriebsanweisung Seite 4

ENGLISH
safe usage of the unit and information about
danger that can be caused by its improper
usage.
•
Do not leave children unattended to prevent
using the unit as a toy.
•
For children safety reasons do not leave poly-
ethylene bags used as packaging unattended.
Attention! Do not allow children to play with
polyethylene bags or packaging film. Danger of
suffocation!
•
Transport the unit in the original package only.
• Keep the unit out of reach of children and dis-
abled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD
USAGE ONLY
BEFORE THE FIRST USE
After unit transportation or storage at low
temperature, it is necessary to keep it for at
least two hours at room temperature before
switching on.
•
Unpack the unit completely and remove any
stickers that can prevent unit operation.
•
Check the unit for damages, do not use it in
case of damages.
•
Before switching the unit on, make sure that
your home mains voltage corresponds to the
unit operating voltage.
•
Install one of the attachments on the unit body
(4) so that the symbol «▼▼» is above the
attachment lock button (7). Turn the attach-
ment clockwise until clicking. If the attach-
ment is set properly, you will hear the lock
button (7) click.
•
To remove the attachment, press the button
(7) downwards and turn the attachment coun-
terclockwise.
Note: Install or change the attachments only
when the unit is unplugged.
•
Insert the power plug into the mains socket.
•
Make sure that the switch (3) is in the lower
position «0».
•
Select the required operation mode using the
switch (3):
«0» – the unit is off,
«1» – low air flow speed,
«2» – high air flow speed,
«С» – «cool shot» mode.
Notes:
During the first operation some foreign smell
and a small amount of smoke from the heat-
ing element is possible, this is normal.
VT-2509.indd 4
If the unit is switched on with the switch (3),
the operation indicator (2) will be lighting.
•
Wind a small lock on the brush.
•
Switch the unit on and dry your hair for several
seconds, adjusting the air flow speed with the
switch (3).
• Remove the lock from the brush.
•
This model has a "cool shot" function, use it to
fix your hairstyle. To switch the «cool shot» on,
set the switch (3) to the upper position «C».
•
After you finish styling, set the switch (3) to the
«0» position and unplug the unit.
•
Place the unit on a flat heat-resistant surface
and let it cool down completely.
Notes:
Before making a break in operation, switch
the unit off with the switch and put it on a flat
heat-resistant surface.
Avoid contact of hot surfaces of the unit with
your face, neck or other parts of your body.
Do not comb your hair right after styling, let
it cool off. Carefully divide the locks with your
fingers to make them look naturally.
Do not block the air inlet grid (5) when using
the unit.
Avoid getting of hair into the air inlet grid dur-
ing unit operation.
ATTACHMENTS
Nozzle (8)
The nozzle (8) allows to direct a narrow high-
intensity air flow at a definite hair lock.
Attachment comb (9)
The attachment comb (9) creates the effect of
natural volume on hair of different length and
provides soft drying.
Brush attachment with pullout bristles (10)
The brush attachment (10) makes it easier to
unroll the lock after drying. To remove a lock from
the attachment, move the lever (11) to the utmost
right position.
Brush attachment (12)
The brush attachment (12) helps to add volume
to your hair and to make curly locks.
Hair care
To get the best results, wash your hair with sham-
poo (before drying and styling), dry it with a
towel to remove excessive moisture and comb
your hair.
4
19.09.2014 12:57:52