Jacuzzi lodge MLS Vorinstallationsblatt Seite 17

(
SUPPLEMENTARY HEATER OPTIONAL
Power supply (x) Total consumption
Volt Hertz Ampere
220-240 ~ 50/60
26
(k)
HEAT EXCHANGER
- Primary inlet MAX temperature ....................................................50 °C
- Connections .......................................................................................... 3/4"
- Primary circuit flow rate ........................................................... 38 l/min
- Primary pressure drop ....................................................... 0,271 M H
The electrical system that powers the hot tub must absolutely
be sized for maximum consumption (as indicated in the respec-
tive tables).
Weights
L M
ODGE
average volume
Net weight
of use
kg litres
~ 260 ~ 880
support concentrated load
area on support area
m 2 kg/ m
~ 3 ~ 453
L L
ODGE
average volume
Net weight
of use
kg litres
~ 348 ~ 1420
support concentrated load
area on support area
m 2 kg/ m
~ 3,95 ~ 550
L S
ODGE
average volume
Net weight
of use
kg litri
~ 245 ~ 750
support concentrated load
area on support area
2
m kg/ m
~ 2,45 ~ 488
User safety
If installed by qualified personnel in compliance with the in-
structions in the enclosed installation manual, the system does
not present any risks for the user. However, safety is also contin-
gent upon appropriate use, according to the provisions in the
)
kW
6
(j)
water volume
Total max. weight
MAX
litres
~ 1100
2
water volume
Total max. weight
MAX
litres
~ 1820
2
water volume
Total max. weight
MAX
litri
~ 950
2
respective manual, while the user must delegate the operations
described in the installation manual to qualified personnel.
It is important to make sure that personnel tasked to install
or manage the system are qualified as per legal requirements in
effect in the country where installation is carried out.
Positioning the hot tub
( 4) The hot tub can be set against a wall, as shown, leav-
ing the three sides free relative to the electromechanical
components located under the hot tub, making sure that it
O can be inspected and the necessary maintenance can be per-
2
formed.
If you want to install the hot tub against multiple walls, a
space must be guaranteed for the removal of the panels and
for any maintenance, and access must be guaranteed to the
equipment in the tub compartment.
Prolonged sun exposure could damage the material
of which is made the hot tub shell, due to its capac-
ity to absorb heat (dark colours in particular). Don't
leave the hot tub to sun exposure without adequate
protection when not in use (cover thermal, gazebo,
kg
etc.). Any damage arising by not following these
~ 1360
warnings are not covered by the guarantee.
The hot tub can be installed in various ways:
- ( 4) free standing on the floor or on a specifically prepared
base.
- ( 5) Semi-built in, so that only the base of the hot tub is
built-in and therefore the side cover panels remain free. In this
case, it is appropriate to prepare some removable under-frames
(in marine plywood, etc.) that, besides aesthetically completing
kg
installation, allow the panels to be removed more easily. The size
~ 2168
of the built-in space in the floor is obtained from that of the base
of the hot tub (
NOTE: between the floor embedding and the panels, it is ad-
visable to leave enough manoeuvring space all around the
hot tub in order to remove the panels (detail A).
- ( 6) built-in, with the tub edge flush with the floor.
( 7) In this case, a base support must be made under the
bottom of the tub (in concrete and steel beams, (detail 1).
kg
Access to the hosing must be ensured and to all other electro-
~ 1195
mechanical parts that are under the tub, for example by making
a passage along the outer perimeter, that is wide enough (about
80 cm) to carry out all electrical and hydraulic connections and
any maintenance operations (detail 2). This passage can be
closed using removable under-frames (detail 3), with suitable
supports (detail 4).
It is also necessary to make arrangements for draining, in case
of stagnant water (detail 5) and guarantee suitable ventilation.
In any case, you will need to provide a support base that is
suitable for the load of the hot tub as shown in the table of
weights above.
17
1a-1b-1c).