Cleaning And Care - Vitek VT-2512 R Betriebsanweisung

•
Set the telescopic attachments (12 or 14) to the po-
sition 3 and 6 for very short haircut. To leave longer
hair, use the positions 7, 9 or 11 of the telescopic at-
tachments (12 or 14).
•
To leave longer hair, take hair locks between your
fingers and cut hair using the hair clipper.
•
You can use the comb (8): lift the hair locks and cut
them with the hair clipper above the comb.
•
Always start cutting from the head back.
•
Set the hair with the comb (8) to reveal uneven
locks.
•
Use the scissors to trim hair.
Step 5 - the final part
In the final stage of hair cutting remove the telescopic
attachment from the unit, turn the blades of the hair
clipper towards the hair and trim hair on the temples and
neck carefully. Do not press on the hair clipper strongly,
there is danger of injuries or cuts when open blades
come in contact with skin.
Cone-shaped haircut
Set the necessary telescopic attachment and start cut-
ting from the head back towards the crown. Cut hair
against hair growth from the head front to the crown and
on the head sides. To get a flat top haircut, use the comb
(8): lift the locks and cut them along the comb. Set the
hair with the comb (8) to reveal uneven locks.
Shaving
The best shaving results are achieved if your skin is dry.
Your skin may need 2-3 weeks to get used to this shav-
ing system.
•
Install the shaving attachment (17).
•
Switch the shaver on, setting the switch (3) to the
position «I».
•
Touching the skin slightly, move the shaver back
and forth and rotationally at a time.
•
After shaving switch the hair clipper off by setting
the switch (3) to the position «0».
•
Clean the shaving attachment (17).
Cutting beard and mustache
Use the trimmers (11, 13) with telescopic attachments
(12, 14) for beard styling; you can also use the detail
trimmer (15).
–
Install the trimmer (11 or 13) on the hair clipper and
install the corresponding telescopic attachment (12
or 14) on the trimmer.
–
Until you learn your hair clipper better, set the at-
tachment combs to the position «9» or «11», de-
pending on the attachment; then you can reduce
the haircut length gradually by adjusting the attach-
ment combs.
–
To cut the beard symmetrically start cutting from the
ear to the chin on the one side of the face, and then
repeat the beard cutting on the other side.
–
When cutting mustache, first comb them and start
cutting from the middle to the corners of the lips.
Note: Always cut off a little amount of hair at a time; if
necessary you can always return to the cut area again
for additional cutting.
–
In the final stage of beard cutting remove the tele-
scopic attachment from the unit, turn the blades of
the unit towards yourself and, slightly pressing the
hair clipper, define the desired contour of the beard.
–
Do not press the hair clipper strongly, there is dan-
ger of injuries or cuts when open blades come in
contact with skin.
–
When cutting hair on the cheeks, move the trim-
mer downwards; move the trimmer upwards on
the neck.
–
After you have cut the beard and mustache, main-
tain their shape.
Trimmer for cutting hair in the ears and nose.
Be careful when using the trimmer for cutting hair in the
ears and nose (16). Insert only the metal tip of the trim-
mer attachment into the auricle or the nostril.
–
Install the trimmer attachment (16) on the hair clip-
per and check if it is set securely.
–
Switch the unit on, setting the switch (3) to the po-
sition «I».
–
Move the metal tip of the trimmer smoothly back
and forth and rotationally at a time; carefully cut hair
in the nose and/or ears.
–
After you finish using the unit, switch the unit off by
setting the switch (3) to the position «0».
–
Use the trimmer (16) only for cutting hair in the ears
and nose.
Face and body trimmer
Use the attachment (19) for shaving narrow places
around the beard/mustache/sideburns, this attachment
is not intended for shaving all the face.
Using the attachment comb (20) you can safely remove
hair on the face and body; besides, you can define the
cutting length, for instance, when shaving brows, by set-
ting the attachment comb (20) into the certain grooves
of the trimmer (19).
–
Set the attachment (19) on the hair clipper body (2).
–
Set the attachment comb (20) into the required
groove of the trimmer (19).
–
Switch the hair clipper on, by setting the switch (3)
to the position «I».
–
Slightly press the attachment comb (20) to the skin
and slowly move the attachment comb (20) along
the hair growth direction.
–
Attachment comb (20) movements should be slow
and controlled.
–
If hair is collected in the attachment comb (20),
switch the unit off, remove the attachment comb
(20) and clean it from the cut hair.
–
After finishing the operation, switch the hair clip-
per off by setting the switch (3) to the position
«0».

CLEANING AND CARE

–
Switch the hair clipper off after the use.
–
Remove all the used attachments from the hair clip-
per and clean them from hair from the inside and
outside, using the cleaning brush (7).
5
ENGLISH