Vitek VT-2512 R Betriebsanweisung Seite 4

ENGLISH
–
Pressing and holding the attachments release but-
ton (1), remove the attachment from the unit body
(2).
–
To install the required attachment insert the lock on
the bottom part of the attachment into the groove on
the rear side of the unit body (2), then, holding the
release button (1), insert the attachment till bump-
ing and release the button (1).
Setting the attachments
–
Telescopic attachment for 40 mm trimmer
Install the telescopic attachment (12) on the trimmer
(11), the lower lock of the attachment (12) should be
fixed on the trimmer (11). You can adjust the cutting
length by moving the attachment against the trimmer
(11) within 3, 5, 7, 9, 11 mm.
–
Telescopic attachment for 30 mm trimmer
Install the telescopic attachment (14) on the trimmer
(13) on the blades side and push it downwards till bump-
ing. You can adjust the cutting length by moving the at-
tachment against the trimmer (13) within 3, 5, 7, 9 mm.
Remove the attachment (14) by moving it up against
the trimmer (13).
–
Attachment comb for the face and body trim-
mer
Insert the attachment (20) into the grooves of the trim-
mer (19); you can adjust the cutting length (3, 6, 9 mm)
by installing the attachment (20) into one of the three
grooves of the trimmer (19).
Lubricating oil
–
To maintain the hair clipper in a good condition, you
should lubricate the trimmer blades (11, 13, 15, 19)
after every use of the hair clipper.
–
For lubricating the blades use only the lubricating oil
(9), supplied with the unit.
–
The trimmer for cutting hair in the ears and nose
(19) does not need lubricating.
Operating the hair clipper
•
For cordless use of the unit, charge the battery fully.
•
Install the required attachment.
Note: For corded use of the unit, insert the connector
of the adapter (10) into the slot (5) on the unit body (2)
and connect the adapter (10) to the mains.
•
Switch the unit on by setting the switch (3) to the po-
sition «I», the indicator (4) will light up red.
•
After finishing the unit operation switch it off by set-
ting the switch (3) to the position «0».
Note:
–
Always switch the hair clipper off during breaks in
operation.
–
While corded unit operation switch the hair clipper
off and unplug the adapter before changing the at-
tachments.
Haircutting
Use the trimmers (11, 13) with corresponding telescopic
attachments (12, 14) for hair cutting.
You can use the detail trimmer (15) for creative haircuts
on short hair.
•
Hair should be clean while cutting.
•
You can also cut wet hair.
•
Install the required trimmer (11, 13 or 15).
•
Before cutting hair switch the hair clipper on, by set-
ting the switch (3) to the position «I» and make sure
that hair clipper operates normally and the blades
move smoothly. If there is excess oil on the blades,
remove it with a dry cloth.
•
Switch the unit off by setting the switch (3) to the
position «0», then install the corresponding tele-
scopic attachment (12 or 14) on the trimmer (11
or 13).
•
Seat the person so that his/her head is approxi-
mately at your eye level, cover the person's shoul-
ders with a towel and set hair with the comb (8).
•
Switch the unit on, setting the switch (3) to the po-
sition «I».
Reminder
–
Always cut off a little amount of hair at a time; if nec-
essary you can always return to the cut area again
for additional cutting.
–
The best haircutting results are achieved on dry
hair, not wet.
–
Set the hair with the comb (8) to reveal uneven
locks.
–
It is better to leave longer hair after cutting for the
first time.
–
After learning the unit better, you will be able to ar-
range your hair in any style you need.
Step one
Install the telescopic attachment (12 or 14) to the posi-
tion 3 or 6. Switch the unit on using the power switch
(3), setting it to position «I». Hold the unit with the
blades pointed upwards. Start the haircutting from the
beginning of the hair growth. Slowly move the clipper
upwards. This way cut the head back area at neck bot-
tom and near the ears.
Step two
Switch the hair clipper off by setting the switch (3) to
the position «0»; depending on the used telescopic at-
tachment (12 or 14) set it to the position 9 or 11, switch
the hair clipper on and continue cutting hair near the
top of the head.
Step 3 – cutting temples
Switch the hair clipper off; depending on the used
telescopic attachment (12 or 14) set it to the position 3
or 6 and cut hair on the temples. Then, depending on
the used telescopic attachment (12 or 14), set it to the
position 9 or 11 and continue cutting hair towards the
top of the head.
Step 4 – cutting the top of the head
Using the telescopic attachment in the position 9 or 11
(attachment 14), cut the hair from the top of the head
towards the crown against the hair growth direction.
•
You can cut hair both against and along the hair
growth direction, but keep in mind that hair cut
against the growth direction will be shorter than the
hair cut along it.
4