Adjusting The Ceiling Cover Plate; Mains Connection Of The Control Unit; Safety Power Cut - Kindermann compact2 series Installations- Und Bedienungsanleitung

4.6 Adjusting the ceiling cover plate

When the lift is in its upper position the cover plate should be level with the surface of the false ceiling. One method is to
fasten the screws of the extension elements on the cover plate only slightly, to adjust the upper stop position, to move the
lift upward into this position and to press the ceiling cover plate manually against the surface of the false ceiling. Afterwards
lower the lift again and tighten the screws. Also the screw

4.7 Mains connection of the control unit

Safety instructions:
4.7 Mains connection of the control unit
• The switches and controls must not enable simultaneous up and down commands. This would damage the unit.
Safety instructions:
Only use mechanical or electrical switches!
!
• The switches and controls must not enable simultaneous up and down commands. This would damage the unit.
• There must be an interval of more than 0.5 seconds between an up and down command. Otherwise high voltage could
Only use mechanical or electrical switches!
damage the motor.
• There must be an interval of more than 0.5 seconds between an up and down command. Otherwise high voltage could
• Condensor motors are suitable only for short time operaqtion (approx. 4 minutes). If the motor is overheated during a
damage the motor.
test drive or when in operation, it is switched off automatically.In such a case let the motor cool down approx. 15 minutes.
• Condensor motors are suitable only for short time operaqtion (approx. 4 minutes). If the motor is overheated during a
• Check whether the two carrying ropes are of the same length and are wound up tightly and orderly on the shaft of the
test drive or when in operation, it is switched off automatically.In such a case let the motor cool down approx. 15 minutes.
motor.
• Check whether the two carrying ropes are of the same length and are wound up tightly and orderly on the shaft of the motor.
• Make sure that the projector is brought in upward position only after it has been switched off and has cooled down. • Make sure that the projector is brought in upward position only after it has been switched off and has cooled down.
• If the lift is operated by a media control, the programming of the media control must be done likewise and the safety
• If the lift is operated by a media control, the programming of the media control must be done likewise and the safety
instructions must be observed.
instructions must be observed.
The lift can be controlled via:
1. Switch/button up/down
The lift can be controlled via:
(5944 000002)
1. Switch/button up/down
2. Key switch
(5944 000 002)
(5944 000001)
2. Key switch
(5944 000 001)
3. Radio remote control
(5699 000 020)
3. Radio remote control
(5699 000 020)
After adjusting the stop positions you must disconnect the external programming unit and connect the wiring of the motor
according to the following circuit diagram.
After adjusting the stop positions you must disconnect the external programming unit and connect the wiring of the motor
according to the following circuit diagram.
Circuit diagram installation of switches/buttons
Circuit diagram installation of switches/buttons
Mains
Projector
switch
Switch for
rope control
blue black
yellow/green
Projector
Ceiling lift
Attention: Make sure that the wiring of the motor control is not mixed up (brown = up, black = down) when inserting the cables
!
Attention: Make sure that the wiring of the motor control is not mixed up (brown=up, black=down) when inserting the cables
for the switch/button (up/down) to the lift. Use only certified protected cables.
for the switch/button (up/down)to the lift. Use only certified protected cables.
The parallel wiring of several condenser motors is not allowed (ceiling lift, electrical screen...).
!
In such a case use a splitter with separate inputs for each motor.
Attention: The parallel wiring of several condenser motors is not allowed (ceiling lift, electrical screen...).
In such a case use a splitter with separate inputs for each motor.

4.8 Safety power cut

The ceiling lift is equipped with a safety power cut. The condenser motor stops automatically, if the movement of the lift is
obstructed and the carrying rope is no longer under tension.
4.8 Safety power cut
The ceiling lift is equipped with a safety power cut. The condenser motor stops automatically, if the movement of the lift is
obstructed and the carrying rope is no longer under tension.
4. IR remote control
(5699000 021)
5. 2 relays contacts of a media control
system and a motor control unit
(5699000 022)
Splitter
blue
Switch
button
black
brown
brown
yellow/green
socket
Power socket
ceiling lift
on the projector holder
b
4. IR remote control
(5699 000 021)
5. 2 relays contacts of a media control
system and a motor control unit
(5699 000 022)
Wiring diagram installation of switches/buttons
Wiring diagram installation of switches/buttons
Mains
green/yellow
blue
black
Mains
Wall switch/button
e. g. 5944 000 002
must be secured with a spanner.
8
Splitter
building
green/yellow
blue
brown
black
Cable between splitter
and socket at least 6-pin
(e. g. NYM 7x1.5 mm )
2
Socket for
button/
switch (building)
Safety switch
blue
gn/ye
bl
br
black
Motor
Socket on lift
29