Mounting The Projector; Prerequisites Of The Projector; Inserting The Projector - Kindermann compact2 series Installations- Und Bedienungsanleitung

Wiring diagram programming unit
green/yellow
blue
black
Mains
standard operation
Connection clamp
of programming unit
7466000102
7466 000 100
7466 000102
2
1
Mains
Programming mode
Mains
Media controlled operation
/ . along the concertina elements. All the wiring to the lift resp. projector goes through the
5b

4.2 Mounting the projector

.
1

4.2.1 Prerequisites of the projector

Three or four drill-holes (M3, M4, M5 or M6) on the bottom, distance between the drill-holes between 75 and 370 mm.
Max. weight: 20 kg. Mounting with only 3 carrying arms is possible.
Supplied with 4 sets of screws with washers M3, M4, M5, M6.
Required tools:
࿼ 1 x screw driver
࿼ 1 x Allen key No. 3
࿼ 2 x spanners 10 mm

4.2.2 Inserting the projector

• The projector spider
off sidewards (illustration 1) after loosening the two screws
likewise (illustration 2).
• With the help of the distance bolts you can even out different levels of the drill-holes in the projector bottom.
• Loosen the centre screw
• Put your projector upside down on a soft surface (illustration 3).
• Find out the proper set of screws
distance bolts. Use the suitable washers on both sides.
At least 3 distance bolts must be inserted. Do not use any glue or grease. If the mounting is not done correctly, the
•
!
projector can drop. Danger of accidents or injuries. If the distance bolts are longer than the drill-holes of your projector,
use additional washers to avoid damages of your unit.
with four carrying arms and distance bolts are attached to the projector holder
9
• Fasten the centre screw
Secure the connection by fastening the two screws through the slots of the cross bar.
of the projector spider with the 2 spanners 10 mm (illustration 2).
b
Splitter
(building)
green/yellow
blue
brown
black
Cable between
splitter and socket
at least 6-pin
(e. g. NYM 7x1.5 mm 2 )
Socket
for switch/
socket
building
Socket / lift
Operation signal
1
2
Programming unit Standard
Programming unit
7466 000102
Standard 7466 000 100
with four carrying arms and distance bolts are attached to the projector holder
9
of the projector spider with the 2 spanners 10 mm (illustration 2).
b
that fit into the drill-holes of your projector and fasten the carrying arms with the four
10
of the carrying arms. Hang the pre-mounted unit into the projector holder
b
through the slots of the cross bar
a
Safety switch
Lower the lift down to the pre-programmed bottom position
and insert the signal and control cables to the projector into
the spiral cable guides
blue
All the wiring to the lift resp. projector goes through the
gr/ye
openings on the upper metal frame
blue
Only use flexible cables. The required cable length within the
br
unit varies between 2.5 m and 3.6 m (Compact
spiral cable guide with the help of the clips to the concertina
black
elements so that the wiring can't be damaged by the
up and down movements of the lift.
Caution:
!
Motor
The switch is not suitable for permanent operation but only
for moving the lift up and down.
Note:
!
If the motor switches off before the lift has reached the
end position, it is possible to overcome the locking by
shortly reversing the movement of the lift and then
readjusting the end position.
through the slots of the cross bar
a
/ along the concertina elements.
5a 5b
120).
2
and can be attached again
7
and can be
8
and can be
7
.
1
120). Fix the
2
and can be taken
8
on the cross bar .
8 7
25