Applicable Controls - Toshiba RAV-SM406BTP-E Installationsanleitung

9

Applicable controls

REQUIREMENT
• When you use this air conditioner for the first time, it
takes approx. 5 minutes until the remote controller
becomes available after power-on. This is normal.
<When power is turned on for the first time after
installation>
It takes approx. 5 minutes until the remote controller
becomes available.
Approx. 5 minutes
"SETTING"
"SETTING"
Power on
goes out
flashes
<When power is turned on for the second (or later)
time>
It takes approx. 1 minute until the remote controller
becomes available.
Approx. 1 minutes
"SETTING"
"SETTING"
Power on
goes out
flashes
• Normal settings were made when the indoor unit was
shipped from factory.
Change the indoor unit settings as required.
• Use the wired remote controller to change the
settings.
* The settings cannot be changed using the
wireless remote controller, sub remote controller,
or remote-controller-less system (for central
remote controller only). Therefore, install the
wired remote controller to change the settings.
77-EN
 Basic procedure for changing
settings
Change the settings while the air conditioner is not
working. (Stop the air conditioner before making
settings.)
CAUTION
Set only the CODE No. shown in the following table: Do
Remote NOT set any other CODE No.
controller is
If a CODE No. not listed is set, it may not be possible to
available
operate the air conditioner or other trouble with the
product may result.
* The displays appearing during the setting process
differ from the ones for previous remote controllers
(AMT21E, AMT31E). (There are more CODE No.)
Remote
controller is
available
4
6
1 5 2
1
Push and hold button and "TEMP."
button simultaneously for 4 seconds or
more. After a while, the display flashes as
shown in the figure. Confirm that the CODE
No. is [01].
• If the CODE No. is not [01], push
clear the display content, and repeat the
procedure from the beginning. (No operation of
the remote controller is accepted for a while
after button is pushed.)
(While air conditioners are operated under the
group control, "ALL" is displayed first. When
is pushed, the indoor unit number
displayed following "ALL" is the header unit.)
(* Display content varies with the indoor unit
model.)
– 39 –
2
Each time
unit numbers in the control group change
cyclically. Select the indoor unit to change
settings for.
The fan of the selected unit runs and the louvers
start swinging. The indoor unit for change settings
can be confirmed.
3
Specify CODE No. [
buttons.
4
Select SET DATA [
buttons.
5
Push button. When the display changes
from flashing to lit, the setup is completed.
• To change settings of another indoor unit,
repeat from Procedure
• To change other settings of the selected indoor
1
unit, repeat from Procedure
3
Use button to clear the settings. To make
settings after
2
Procedure .
6
When settings have been completed, push
button to determine the settings.
When button is pushed,
and then the display content disappears and
the air conditioner enters the normal stop
mode.
(While is flashing, no operation of the
remote controller is accepted.)
button to
 External static pressure
button is pushed, indoor
settings
Set up a tap change based upon the external static
pressure of the duct to be connected.
To set up a tap change, follow to the basic operation
1
procedure (
• Specify [5d] to the CODE No. in procedure
• For the SET DATA of procedure
DATA of the external static pressure to be set up
from the following table.
<Change on wired remote controller>
] with "TEMP." /
SET DATA
0000
] with "TIME" /
0001
0002
0003
0004
0005
2
.
0006
3
.
The list above is when SW501-1 and SW501-2 is OFF.
button was pushed, repeat from
flashes
2 3 4 5 6
→ → → → →
).
3
.
4
, select a SET
External static pressure
40 Pa
30 Pa to 3 HP (Factory default)
65 Pa
50 Pa 4 to 6 HP (Factory default)
80 Pa
100 Pa
120 Pa
78-EN