QUAMAR M80 Automatico Anweisungen, Anleitungen Seite 17

GB
- double dose: push the button with two cups
- manual dose: push at the same time the button with a cup
+ the button with two cups
during the distribution of the milled coffee, the display visu-
alize "run" to inform that the apparatus is in function.
2. programming milled dose: the distribution duration of the
milled coffee is defined from t1+t3 (single dose) and t2+t4
(double dose). Times T1, t2, T3, t4 can be programmed in
this way:
a) regulation of time T1: press key "+" and visualize on the
display "t1xx" where xx is from 00 to 99 cent of second.
Press now on "+" and "- "value xx to increase or diminish.
After 2s the set up value is recorded and you're out from the
programming mode.
b) regulation of time T2: press key "-" and visualize on the
display "t2xx" where xx is from 00 to 99 cent of second.
Press now on "+" and "- "value xx to increase or diminish.
After 2s the set up value is recorded and you're out from the
programming mode.
c) regulation of time T3: switch off and switch on the ma-
chine, for 3s will flash written "the 8888". Press the key "a
cup" and at the same time "- " visualize on the display "t3xx"
where xx go from 01 to 99 seconds. Press now on "+" and
"- "value xx to increase or diminish. After 2s the set up value
is recorded and you're out from the programming mode.
d) regulation of time T4: switch off and switch on the ma-
chine, for 3s will flash written "the 8888". Press the key "two
cups" and at the same time "+" visualize on the display "t4xx"
where xx go from 02 to 99 seconds. Press now on "+" and
"- "value xx to increase or diminish. After 2s the set up value
is recorded and you're out from the programming mode.
e) setting of the counter: switch off and switch on the ma-
chine, for 3s will flash written "the 8888". Press key "+" and,
at the same time "- " The counter of the distributed doses
is annulled.
f) qualification to the programming: switch off and then
switch on the machine, for 3s will flash written "the 8888".
Press at the same time the keys "a cup" + "two cups" will
visualized "on" if the regulation dose is blocked, "off" if quali-
fied. Press now "+" or "-" to change state. After 5s it is re-
turned to the normal operation.
SECURITY SYSTEM TO AVOID THE ACCESS TO THE
MOVING PARTS (VALID FOR ALL THE MODELS AND
VERSIONS)
There are many protection systems (already described) to
avoid the access to the rotary parts as the safe screw on
the beans container and the metal ring, the fixed cone of
protection inside of the beans container and the protection
in metal placed in front of the milled coffee exit. All these
devices are conceived in order to protect who use the ap-
paratus. For this reason, we underline that you don't have
absolutely remove or modify them and, for any problem of
malfunctioning, you have to contact technical staff which
will know how to help you.
14
COFFEE GRINDER DOSER T48
COFFEE GRINDER DOSER T48
OPERATION
Before inserting the plug in the socket or the main switch
upstream from the machine, ensure that the switch on the
machine is on position "0".
Insert the shutter that closes the container and check that
it slides in its seat.
Fit the container in its seat, pressing at the side with your
fingers until it is firmly in place. Then fix it to the ring nut of
milling regulation with the appropriate screw supplied with
the apparatus, match the hole on the beans container with
the one on the ring nut.
If your coffee grinder ha san automatic switch, check that
the lever is in the position indicated. The coffee grinder is
now ready for work.
Pour the coffee beans into the top container. Open the shut-
ter. Insert the plug in the socket or turn on the main switch
upstream from the machine, then turn the machine switch
to position "I".
Check the grain size of the ground coffee; each grinder is
set for medium-fine grain. If you're not satisfied with this re-
sult you must proceed as follows:
Turn the ring nut to the LETF for finer grain or to the RIGHT
for coarser grain.
Note: the coffee grinder is equipped with a security cone
fixed on the head of beans hopper.
ADJUSTING THE QUANTITY DELIVERED
To adjust the quantity, turn the adjusting nut. Turn to the
LEFT to increase the quantity, to the RIGHT to decrease it.
The dosing device can deliver from 4gr to 9gr.
To set the amount you want, take 10 doses (ten pulls of the
lever) from the doser and weight the coffee that comes out,
in this way you can calculate the weight of each dose.
MAINTENANCE AND CLEANING
OF ALL THE APPLIANCES
Any maintenance or clearing must be performed only after
the machine is unplugged and has cooled down. To avoid
dragging or scratch on the body, never use cloth, sponge or
detersive with abrasive action. To clean the appliance use
a well-wrung damp cloth and specific products for stainless
steel, aluminium, paint, chrome.
Components that come into contact with food can be clea-
ned separately by hand with water and washing-up liquid.
Do not put them in the dish washer.
The empty container may be washed separately with water
and suitable detergent.
Before removing the container, remember to close the shut-
ter and switch on the coffee grinder; this will remove any
beans left in the grinding area.
From time to time check the inside of the doser to make
sure there are no deposits and if you have to remove any,
REMEMBER TO DISCONNECT THE MACHINE FROM
THE MAINS. On ECONOMY models, remember to switch
off the grinder after you have ground a certain amount of
coffee, to prevent the ground coffee from overflowing from
the cover of the doser.