Operation - QUAMAR M80 Automatico Anweisungen, Anleitungen

GENERAL WARNINGS
Read thoroughly and stick closely to the instructions and
warnings.
Always remove the plug from the socket before carrying out
any maintenance or clearing of the appliance.
SINGLE PHASE models are supplied complete with cable
and plug for connection to the socket.
TREE PHASE models are provided with a cable which must
be connected to the mains by a qualified electrician or a
skilled installation technician.
Any tempering with the machine or connections not com-
plying with the above indications invalidate the manufactu-
rer's guaranty.
PARTICULAR WARNINGS
Never tamper with the machines anyway. For all interven-
tions or tampering on the machines, always apply to the
authorized centre service. Never pull the power cable to
remove the plug from the socket. Only use the appliance
for the purposes it is meant for. Position the appliance a
minimum of 5cm from walls so as to allow good aeration.
Keep the appliance away from sinks and incompetent peo-
ple. Never switch on a machine that seems to be faulty. Use
only original accessories and parts. To avoid the danger of
fire, never cover the appliances. Unplug the appliance from
the mains when it is not in use. Let the appliance to cool
down before moving it. In the interest of safety, the applian-
ces must always be considered as live. The motor is equip-
ped of a thermal sensor that switch off the feeding when
high temperatures are reached. If this happen unplug the
machines from the mains and let it cool down, then contact
technical staff. Do not repair by yourself.
If the coffee grinder is to remain inactive for a long period,
clean it carefully, dry the top container and leave it open.
INSTRUCTIONS
COFFEE GRINDER DOSER M80-M1
COFFEE GRINDER DOSER M80-M1
Appliances to ground coffee beans.
ATTENTION
Moving parts.
OPERATION INTERVAL OF THE MACHINE
Respect the following cycle of use of the machine: 6 min
OFF/30s ON.

OPERATION

Before inserting the plug in the socket or the main switch
upstream from the machine, ensure that the switch on the
machine is on position "0".
Insert the shutter that closes the container and check that
it slides in its seat.
Fit the container in its seat, pressing at the side with your
fingers until it is firmly in place. Then fix it to the ring nut of
milling regulation with the appropriate screw supplied with
the apparatus, match the hole on the beans container with
the one on the ring nut.
If your coffee grinder ha san automatic switch, check that
the lever is in the position indicated. The coffee grinder is
now ready for work.
Pour the coffee beans into the top container. Open the shut-
ter. Insert the plug in the socket or turn on the main switch
upstream from the machine, then turn the machine switch
to position "I". For security issues, the customer not have to
remove any type of screw on the coffee grinder. This ope-
ration is only concurred by qualified technicians and after
detached the apparatus from the feeding net.
Check the grain size of the ground coffee; each grinder is
set for medium-fine grain. If you're not satisfied with this re-
sult you must proceed as follows:
COFFEE GRINDER DOSER M80:
1) Press the ring nut pawl downwards
2) Turn the ring nut to the LEFT for finer grain or to the
RIGHT for coarser grain.
To avoid the removal of the metal ring with the consequent
possibility to have free access to the milling group, place
the screw in one of the two holes allowing the widest re-
gulation.
COFFEE GRINDER DOSER M1:
Turn the ring nut to the LEFT for finer grain or to the RIGHT
for coarser grain.
ADJUSTING THE QUANTITY DELIVERED:
To adjust the quantity, turn the adjusting nut. Turn to the
LEFT to increase the quantity, to the RIGHT to decrease it.
The dosing device can deliver from 4gr to 9gr.
To set the amount you want, take 10 doses (ten pulls of the
lever) from the doser and weight the coffee that comes out,
in this way you can calculate the weight of each dose.
M80 - M1 "ON DEMAND" VERSION
Operation
1. before inserting the plug in the socket or turning on the
main switch upstream from the machine, ensure that the
switch on the machine in on position "0". Insert the shutter
that closes the top container and check that it slides in its
seat.
Fit the container in its seat, pressing at the side with your
fingers until it is firmly in place, then fix it to the ring nut of
milling regulation with the appropriate screw supplied with
the apparatus, match the hole on the beans container with
the one on the ring nut.
The coffee grinder is now ready for work. Pour the coffee
beans into the top container. Open the shutter and insert
the plug in the socket, then turn the machine switch to po-
sition "I". Now the display will be ignited visualizing symbol
"8888" blinking for 3s; during this period it is possible to en-
ter in the programming modality (see point 2).
At rest it comes visualized the number of doses previously
distributed (from 0 to 9999). Put the door filter in the ap-
propriate staple and then is possible to proceed with the
distribution of the milled coffee in this way:
- single dose: push the button with a cup
GB
13