Disclaimer; Safety; Operators; Service Technicians - Ranpak PadPak CC Betriebsanleitung

PadPak CC
®
PREFACE
i
This operator manual is made in
the original language.
This operator manual is intended for the operator of this
converter.
This operator manual belongs with
i
the converter. A copy should be
kept with the converter at all times.
In the event of the converter being transferred, all
documentation must be transferred with the converter.

Disclaimer

The manufacturer and its authorized distributor are not
liable for any accidents or damages resulting from the
failure to comply with warnings or instructions depicted
on this converter or contained in this operator manual,
including:
- Improper use or maintenance
- Use for applications or under conditions other than
those outlined in this operator manual
- Use of unauthorized parts
- Repairs or modifications made without the permission
of the manufacturer
- Unauthorized alterations to the converter such as:
a) Alterations to the control system
b) Welding, mechanical treatments etc.
c) Extensions to the converter or the control system
The manufacturer and its authorized distributor are not
liable for:
- Indirect damages caused by errors or malfunctions
of the converter (e.g. damages to products, company
interruptions, delays, etc.).

SAFETY

This converter has been designed for safe use in
conformance with the application, conditions and rules
described in this operator manual. Anyone that works with
or on this converter must read the operator manual and
follow the instructions carefully.

Operators

Only those who read and understand the Sections "Safety"
and "Operator Instructions" should operate the converter.
Special training is not required.
Operator tasks include:
• Loading and feeding the paper bundles
• Operating the converter
• Weekly maintenance (see section 3.8)
◦ Remove paper scraps
◦ Remove excessive paper dust

Service technicians

Only service technicians employed by Ranpak or a Ranpak
distributor who are in possession of a certificate issued
by Ranpak service department are permitted to conduct
service on the converter. For these individuals, a separate
service manual is available.
PadPak CC
®
Operator Manual - EN

Rules of Safety

• Safety devices are not allowed to be switched off or
removed
• The emergency stop must always be in reach of the
operator (if applicable)
• Do not remove or cover warning labels
• Do not reach inside the converter
• Keep the working area clean and free of obstacles
• Unplug converter and gather all loose cords before
moving the converter
• Pay attention when using hand tools such as knives,
scissors etc, due to the risk of cutting
• Ensure that:
◦ cords cannot be damaged
◦ the converter is acclimatised when taken from a
cold to a warm area.
◦ the working area is sufficiently lit
◦ the working area is sufficiently ventilated
• Do not use cable reels. When using an extension cable,
note that the diameter must be at least 14AWG (1,5
mm2) with a maximum length of 33 ft. (10 m)
• Plug the converter always into a grounding-type wall
socket
• Pay attention to ergonomic factors such as lifting,
bending, reaching, etc. during work on the converter

Improper Use

The following applications or acts are not suitable for the
converter, and constitute improper use of the converter:
• Use of materials other than those produced by Ranpak
and intended for use in the converter
• Use outside or in a humid area
• Use in areas subject to an explosion hazard
• Washing or cleaning the converter with excessive
quantities of water
• Standing on the converter or hanging from it
• Placing objects against or on top of the converter
• Moving the converter while it is functioning or connected
to the AC power supply.

Work Area

In order to operate the converter, you need a 1 meter (3
foot) wide, open work area in front of the converter. From
this space, all operating actions can be carried out.

Constructive Safety Provision

Emergency Stop
In order to stop the converter in an emergency situation,
the converter is equipped with an Emergency Stop button.
The Emergency Stop button is the red button at the front
panel of the converter, which will immediately stop the
converter when pressed.
Once pressed, the Emergency Stop button blocks the
operation of the converter and will cause a red light on the
converter to light up. The converter cannot be restarted
until the Emergency Stop button is released. To release
the Emergency Stop button, twist the red knob.
EN
i