Vitek VT-1838 R Die Betriebsanweisung Seite 8

ENGLISH
Remove the dust container (8) pressing the
3.
button (6) and pulling it by the handle (7)
(pic. 1).
Detach the water container (11) having
4.
opened the clamps (9) (pic. 2).
Pour dirty water out of the container (11)
5.
wash it thoroughly with warm water, and then
dry it.
Remove heavy dust and trash from the block
6.
of filters (31) having opened the lower lid (32).
For this purpose pull the clamp (33) towards
yourself.
Note: Place the block of filters (31) over a
dustbin.
Disassemble the block of filters (31) having
7.
opened the clamps (30).
Take the foam protection (35) and the foam
8.
filter (34) out.
Wash the dust container lid (8), the block of
9.
filters (31), the foam filter (34) and the foam
protection (35), dry them thoroughly.
Assemble the block of filters (31).
10.
Place the foam filter (34), then the foam pro-
11.
tection (35) back in their places.
Install the dust container lid (8) back to its
12.
place and fix it having closed the clamps (30).
Install the block of filters (31) into the contain-
13.
er (11). Make sure that it is installed properly.
Fix the water container (11) having closed the
14.
clamps (9).
Cleaning the hEPA Filter (38)
НЕРА filter is located in the lower part of the
unit and is intended for prevention of dust and
dirt particles exhaust back to the room being
cleaned.
Note: Take the dust container (8) out before
removing the HEPA Filter (38).
Remove the HEPA filter lid (36) pulling it
1.
upwards by the clamp (37).
Take the HEPA Filter (38) with foam rubber
2.
gasket out,
Wash the HEPA Filter (38) and its foam rub-
3.
ber gasket with warm water and dry them
thoroughly (pic. 3).
Note:
• Wash the HEPA Filter (38) directing the water
jet to the outer side of the HEPA Filter.
• Do not wash filters in a dishwashing machine.
•
Do not dry filters with a hair dryer.
Insert the foam rubber gasket into the HEPA
1.
Filter (38), then install the HEPA Filter back
VT-1838 IM.indd 8
back in its place.
Install the lid (36) in its place, press it until the
2.
clamp (37) clicks.
Attention!
Before inserting the dust container (8) into the
vacuum cleaner body make sure that the filters,
in particular, the HEPA Filter (38), are dry and
there is no moisture inside the block of filters
(31).
Cleaning ofoutlet filter (25)
Regularly clean the outlet filter (25).
Remove the outlet filter grid (24) having
1.
pressed the clamp and pulled the grid (24)
towards yourself.
Remove the outlet filter (25) from the inner
2.
side of the grid (24), wash them under warm
water jet and then dry them thoroughly.
Fix the outlet filter (25) on the inner side of
3.
the grid (24).
Install the grid (24) back in its place.
4.
Note: Check the filters regularly for dirt accumu-
lation and clean them if necessary.
Vacuum cleaner body
Wipe the vacuum cleaner body with a soft
–
damp cloth.
Do not immerse the body, the power cord and
–
the power plug of the unit into water or other
liquids. Provide that no water gets inside the
unit.
Never use solvents or abrasives to clean the
–
surface of the vacuum cleaner.
STORAGE
Before taking the vacuum cleaner away for
–
storage clean its body, the dust container (8)
and the filters (24, 34, 35 and 38).
For easy storing use the attachment holder
–
(20) and the brush storage space (3) when
the vacuum cleaner body is in the vertical
position.
Keep the vacuum cleaner away from children
–
in a dry cool place.
DELIVERY SET
Vacuum cleaner with the filters and the dust
1.
container installed – 1 pc.
Flexible hose – 1 pc.
2.
Flexible hose handle – 1 pc.
3.
Telescopic extension pipe – 1 pc.
4.
Attachment holder – 1 pc.
5.
8
23.05.2012 15:07:31