Jacuzzi sasha mi Montageanweisung Seite 11

m
Do not place the stones in layers! Always try and leave
space between stones, so that hot air coming from be-
low can circulate freely.
✐
■ ( 21) After removing the glazing bead (item 1) install the
sauna roof-frame as indicated.
✐
22) Apply the plastic spacers as indicated.
■ (
✐
■ ( 23) Install the glazing indicated, apply the glazing beads
in the following order: bottom (f-i), top (f-s) and vertical (f-v).
✐
24) Remove the cross bar glazing bead and the cap, and
■ (
install this to the shower-panel.
- Apply the plastic spacers following the previous instructions.
✐
25) Install the shower-glazing following the previous in-
■ (
structions.
✐
26) Remove the cap from the other cross-bar and install
■ (
as indicated.
✐
■ ( 27) Apply the plastic spacers following the previous in-
structions.
✐
28) Install the sauna-glazing following the previous in-
■ (
structions.
✐
29) Check that the structure is plumb and flush, as indi-
■ (
cated, and anchor to the wall with the brackets.
✐
■ ( 30) Thread the drainage column into the shower-frame
and pull upwards (it will be connected to the heater).
Anchor the drainage column to the tub, positioning the later on
the shower-frame.
✐
■ ( 31) Caulk the tub and shower-frame areas of contact.
- Mount the horizontal "Z" profiles as indicated, caulk the entire
area that touches the shower-frame.
NOTE: the horizontal profile must be positioned on the tub.
✐
■ ( 32) Install the vertical "Z" profiles as indicated, caulking
them along the areas that touch the:
- vertical glazing beads (of the divider and shower-panel);
- upright shower-frame.
Connections - 2 / Accessories
✐
■ ( 33) Move the brassware panel close and connect as indi-
cated.
- Connect the building's equipotential line to the equipotential
terminal of the appliance.
✐
■ ( 34) Finish electrical connections.
✐
35) Caulk the indicated areas; move the panel close and
■ (
position it on the vertical shower frame containing the mixer unit
plumbing, as well as the light-cable (they will all be connected to
the shower-roof ).
- Attach the panel on the "Z" profiles (horizontal and vertical, see
✐
29/31) and secure wit the screws removed previously.
✐
36) Apply the metal corner supports to the sauna roof, as
■ (
indicated.
✐
37) Attach the sauna-roof, as indicated.
■ (
✐
■ ( 38) Fix the roof to the walls and apply the covering strips,
using soft double-sided tape and high temperature resistant sili-
cone.
✐
39) Carry out the plumbing indicated.
■ (
✐
■ ( 40 ) Connect the light-cable and attach the roof, as in-
structed.
- Attach the showerhead and relative flexible hose.
✐
■ ( 41) Caulk:
- between the tub and shower-frame;
- on the resting areas of the "L" covers.
Attach these covers to the shower-head.
✐
■ ( 42) Caulk the underside of the internal covers and attach
to the shower-frame, near the glazing, as instructed.
✐
■ ( 43) Caulk the underside of the outer covers and attach to
the sauna and shower frame.
- Place one of the finishing cornices between the frame and cas-
ing, in order to determine the exact position of the latter (the door
hinges may also be installed to fix the casing to the frames).
✐
■ ( 44) Cut a section of magnet equal to the length of the
sauna-door sensor, place the magnet into the frame indicated.
- Insert the door-sensor into the frame and attach with caulk.
- Assemble the glazing frame, thus threading the sensor cable
into teh hole on the sauna-roof until it reaches the electronic
box; connect as indicated.
✐
45) After measuring its length, cut strips of from the sealant
■ (
roll to apply to the glazing, both inside and out, as instructed.
NOTE: it is recommended to cut approx. 5 cm more of the sealant
than the nominal length and then remove any remaining length
once assembly is complete.
- Caulk the joints of the shower sealant (lower corners).
✐
46) Move the top panel close and connect as indicated.
■ (
- Slide in the panel beneath the ceiling and attach to the other
panel as indicated.
- Put on the screw caps.
✐
47) Attach bench supports, as indicated.
■ (
- Put in the two duckboards while careful not to damage the
heater power cable (and any flexible hose of the automatic fill-
ing device).
- Install the top bench as indicated and attach the other bench
below.
NOTE: the top bench may be attached in one of the positions indica-
ted (A or B); detaching the bench from the wall, significantly increases
the user sitting space.
11