Flight Preparation; Taking Off And Controlling The Quadrocopter; Taking Off (Fig. H); Controlling The Quadrocopter - lidl 311499 Gebrauchsanweisung

Flight preparation

Pay attention to the following, before you start
flying the quadrocopter (1):
1. Always place the quadrocopter (1) on an even
surface for take-off.
NOTE: The on/off switch (1d) is situated on
the upper side of the quadrocopter (1).
2. Always move the throttle (2h) and control lever
(2l) slowly and carefully, with sensitivity.
NOTE: After activation, the control lever
springs back to the centre position, and the
quadrocopter rises/lowers to a specific height and
remains there.
3. Keep your attention continuously focused on the
quadrocopter (1) during the flight!
WARNING: Always keep the quadro-
copter in your sights during flight opera-
tions!
4. Do not hang any loads onto the quadrocopter
(1).
WARNING: Check the rotor protection
(1c) (Fig. B) before each flight to ensure
that it is secure and undamaged.
Otherwise there is a risk of damage to the rotor
blades (1a, 1b) during a flight, which may cause
injury.
Taking off and controlling the
quadrocopter
When flying, watch out for foreseeable misuse as
a result of:
• Sudden changes in the weather
• Sudden changes in wind (gusts)
• Loss of visibility
• Direct sunshine (overheating, loss of control as
a result of being blinded by the sun).

Taking off (Fig. H)

1. Turn the quadrocopter (1) to the OFF position
via the switch (1d).
2. Press the on/off switch (2a) on the remote
control (2). The display lights flash (2j).
NOTE: Always switch the remote control (2)
on first.
3. Insert the rechargeable battery (3) into the
quadrocopter (1).
16 GB
4. Press the on/off switch (1d). The control lights
(1g) of the quadrocopter (1) flash alternately
and a signal tone is emitted from the remote
control (2).
5. Slide the throttle (2h) all the way forward, and
then all the way back.
NOTE: This process establishes contact
between the quadrocopter (1) and the
remote control (2).
If the throttle (2h) is not first moved forward and
then back, the quadrocopter (1) remains secured
and will not be ready for flight. Acoustic signals
are emitted from the remote control (2).
The control lights (1g) on the quadrocopter (1)
light up continuously. The quadrocopter (1) is now
ready for flight.
NOTE: The display (2j) shows the speed
and NORMAL mode.
6. Press the button START/LAND (2i), located at
the front of the remote control. The rotor blades
will start to turn.

Controlling the quadrocopter

The integrated height sensor ensures that the
quadrocopter maintains a steady height, and it fa-
cilitates initial flight manoeuvres. You have several
controlling options:
• Ascending/descending (throttle) (Fig. I)
By pressing the throttle (2h) forwards, the rota-
tional speed of the rotors (1a, 1b) is increased.
The quadrocopter (1) will then begin to rise.
By moving the throttle (2h) backwards, the
rotational speed of the rotors (1a, 1b) is de-
creased. The quadrocopter (1) will then begin
to descend.
• Turning left/right (yaw rotation) (Fig. J)
By moving the throttle (2h) to the left or right,
the quadrocopter (1) turns on its vertical axis,
i.e. the quadrocopter (1) rotates to the right or
left.
• Moving forwards/backwards (pitch)
(Fig. K)
By moving the control lever (2l) to the front or
back, the quadrocopter (1) moves in the corre-
sponding direction.