Werbung
English
Digital Projection
TITAN WUXGA/1080p/sx+- 600/700, HD-600, Reference, UC, 3D, Dual 3D
Installation precautions
Connect the LAN cable only to a computer LAN connection. Other similar connectors
may have a dangerously high voltage source.
The projector must be installed only by suitably qualified personnel, in accordance with
local building codes.
The projector should be installed as close to the power outlet as possible.
The power connection should be easily accessible, so that it can be disconnected in an
emergency.
Ensure that there is at least 30cm (12in) of space between the ventilation outlets and
any wall, and 10cm (4in) on all other sides.
Do not install the projector close to anything that might be affected by its operational
heat, for instance, polystyrene ceiling tiles, curtains etc.
The projector weighs approximately 31 kg (68 lbs). Use safe handling techniques when
lifting the projector.
When stacking projectors, the stack MUST be vertical, to ensure that the stresses are
distributed to all frame couplings.
Before installation, make sure that the surface, ceiling or rigging that is to support the
projector is capable of supporting the combined weight of the projector and lens (see
specification for exact weights).
Separate backup safety chains or wires should always be used for each projector.
Do not place heavy objects on top of the projector chassis. Only the chassis corners
and the rigging frame are capable of withstanding the weight of another projector.
Do not stack more than 3 projectors.
Do not drop or knock the projector.
1080p, sx+: The lens release lever should always be set to the locked position to
prevent the lens from falling out.
1080p, sx+: Each time a new lens is fitted to the projector, the calibration procedure
must be carried out. (See User Manual.)
Place the projector in a dry area away from sources of dust, moisture, steam, smoke,
sunlight or heat.
Do not tilt the projector more than ±12° (3D: ±10°) in either direction when in use, as
this may cause serious lamp failure, damage the lamp module and cause extra cost on
replacement. (See User Manual.)
±12° (3D: ±10°)
Page 6
±12° (3D: ±10°)
Rev F June 2011
Digital Projection
TITAN WUXGA/1080p/sx+- 600/700, HD-600, Reference, UC, 3D, Dual 3D
Operation and configuration precautions
Do not make changes to the networking configuration unless you understand what you
are doing, or have taken advice from your Network Manager. If you make a mistake,
it is possible that you will lose contact with the projector. Always double-check your
settings before pressing the APPLY button. Always keep a written note of the original
settings, and any changes you have made.
Software update should NOT be carried out except by, or with the supervision of, Digital
Projection Service personnel.
Compliance with international standards
Noise
GSGV Acoustic Noise Information Ordinance
The sound pressure level is less than 70 dB (A) according to ISO 3744 or ISO 7779.
RF Interference
FCC
The Federal Communications Commission does not allow any modifications or changes to the unit
EXCEPT those specified by Digital Projection in this manual. Failure to comply with this government
regulation could void your right to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant with Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area may cause harmful interference, in which case the
user will be responsible for correcting any interference.
This equipment contains an FCC approved RF transmitter module with FCC ID: R68WIPORT.
European Waste Electrical and Electronic Equipment (WEEE) Directive
Digital Projection Ltd is fully committed to minimising Waste Electrical and Electronic
Equipment. Our products are designed with reuse, recycling and recovery of all components
in mind. To this end, at end of life, your projector may be returned to Digital Projection Ltd or
its agent so that the environmental impact can be minimised.
Rev F June 2011
English
Page 7
Werbung
Kapitel
