Setting Up The System; Setup After Connection - Pioneer PDA-5002 Bedienungsanleitung

Setting Up the System

Setup after Connection

After components have been connected to INPUT1,
INPUT2 or INPUT5, on-screen setup is necessary.
Follow the procedure described below and make settings
as they apply to the type of components connected.
Setting the Screen Mode /
Input Signal Format
1
Switch MAIN POWER on the connection panel to
the on position to turn on the display's main
power.
The STANDBY/ON indicator lights red.
2
Press STANDBY/ON to put the display in the
operation mode.
The STANDBY/ON indicator turns green.
3
Select INPUT1, INPUT2 or INPUT5.
4
Press MENU to display the menu screen.
The menu screen appears.
MAIN MENU
PICTURE SET UP
:
CO NT RA S T
:
BR I GHT .
: :
C L OR O
: :
T N T I
:
:
S A RP H
R S E T E
SELECT
SET
5 Press 2/3 to select SET UP .
MAIN MENU
PICTURE SET UP
I N P UT L A
AUT O P O WER
D I G I T A L NR
H I GH C O T N R A T
P URE C I N E
C L AM P P S I T I O N O
S E T T I N G
V I DE O S I GNA L
SELECT
SET
6 Press 5/∞ to select SETTING, then press SET.
MAIN MENU
PICTURE SET UP
I N P UT L A
AUT O P O WER
D I G I T A L NR
H I GH C O T N R A T
P URE C I N MA E
C L AM P P S I T I O N O
S E T T I N G
V I DE O S I GNA L
SELECT
SET
14
En
INPUT1
OPTION
0
0
0
0
0
ENTER EXIT
MENU
INPUT1
OPTION
:
B E L I N P UT 1
: OF F
OF F
: L OW
: O F F
S
: O F F
M A
: A U T O
: V I D E O
: R G B
ENTER EXIT
MENU
INPUT1
OPTION
:
B E L I N P UT 1
: OF F
OF F
: L OW
: O F F
S
: O F F
: A U T O
: V I D E O
: R G B
ENTER EXIT
MENU
7 Press 2/3 to select the display mode.
S E T T I N G : V G A
SELECT SET
When a component other than a personal computer is
connected, set to "VIDEO".
1 When the input signal has a refresh rate of 31.5 kHz
horizontal / 60 Hz vertical, pressing 2/3 will cause
the display mode to change alternately as follows:
When using INPUT1 or INPUT2:
VIDEO
WIDE VGA
When using INPUT5:
VGA
2 When the input signal has a refresh rate of 48.4
kHz horizontal / 60 Hz vertical, or 56.5 kHz
horizontal / 70 Hz vertical, pressing 2/3 will cause
the display mode to change alternately as follows:
XGA
Note
Setup steps 6-7 are required only when using signals with the
following refresh rates: 1 31.5 kHz horizontal / 60 Hz vertical; 2
48.4 kHz horizontal / 60 Hz vertical, or 56.5 kHz horizontal / 70 Hz
vertical. No manual setup is necessary for signals with other
refresh rates, since adjustments are performed automatically (the
SETTING item will not be displayed).
8
When a component other than a computer is
connected and VIDEO has been selected, press the
5/∞ buttons to select VIDEO SIGNAL.
MAIN MENU
PICTURE SET UP
I N P UT L A
AUT O P O WER
D I G I T A L NR
H I GH C O T N R A T
P URE C I N MA E
C L AM P P S I T I O N O
S E T T I N G
V I DE O S I GNA L
SELECT SET
9
Press SET repeatedly to select the input signal
format.
Selection will change as follows each time SET is
pressed.
RGB
COMPONENT
SET MENU EXIT
VGA
WIDE VGA
WIDE XGA
INPUT1
OPTION
B E L :
I N P UT 1
: OF F
OF F
: L OW
: O F F
S
: O F F
: A U T O
: V I D E O
: R G B
CHANGE MENU EXIT