Automatic Power Off - Pioneer PDA-5002 Bedienungsanleitung

Operations

Automatic Power OFF

The plasma display is equipped with automatic power-
management and auto-power-off functions, which allow
the unit to automatically switch to power-saving mode
when no sync signal is detected.
(A warning message appears on-screen before these
functions operate.)
Notes
÷ Power management settings are supported only when a
computer signal is input to INPUT 1, or when INPUT 5 is
selected.
÷ The auto-power-off function can be used only in those cases
other than the inputs used in the preceding item.
÷ Always turn off the plasma display's main power switch when
not using the display for extended periods of time.
1
Press MENU to display the menu screen.
MAIN MENU
PICTURE SCREEN
:
CO NT RA S T
:
BR I GHT .
: 6 +
R L E V E L .
: 6 0
G L E V E L . +
: 6 0
+
B L E V E L .
:
H E NH AN CE .
:
V E NH AN CE .
R S E T E
SELECT
SET
2 Press 2/3 to select SET UP .
[When computer signal is input to INPUT 1, or
when INPUT 5 is used]
MAIN MENU
PICTURE SCREEN
I N P UT L A B E
POWE R M NA GEME A
C L AMP P S I T I O N O
S E T T I N G
SELECT
SET
[In all other cases]
MAIN MENU
PICTURE SCREEN
I N P UT L A
A U T O P OWE R
C L AMP P S I T I O N O
S E T T I N G
SELECT
SET
20
En
INPUT1
SET UP OPTION
0
0
0
0
0
ENTER EXIT
MENU
INPUT1
SET UP OPTION
:
L I N P UT 1
:
NT OF F
: A U T O
: V G A
ENTER EXIT
MENU
INPUT2
SET UP OPTION
B E L : I N P UT 2
:
O F F O F F
: A U T O
: V G A
ENTER EXIT
MENU
3 Press 5/∞ to select either the POWER
MANAGEMENT or AUTO POWER OFF mode.
[When computer signal is input to INPUT 1, or
when INPUT 5 is used]
MAIN MENU
PICTURE SCREEN
I N P UT L A B E
POWE R M NA GEME A
C L AMP P S I T I O N O
S E T T I N G
SELECT
SET
[In all other cases]
MAIN MENU
PICTURE SCREEN
I N P UT L A
A U T O P OWE R
C L AMP P S I T I O N O
S E T T I N G
4
Press SET to confirm selection of the POWER
MANAGEMENT or AUTO
POWER OFF.
÷ When OFF is selected, the display will continue in
operating mode, regardless of the presence/absence of
an input sync signal.
÷ When POWER MANAGEMENT: ON is selected, if a
sync signal is not detected, a warning message is
displayed for 8 seconds, after which the display
automatically enters the power-saving mode (*1) and
the STANDBY/ON indicator flashes green. If a sync
signal (*2) is input again later, the plasma display
automatically returns to normal operating mode.
*1. Power consumption is about 1 W when INPUT 1 is
used, and about 50 W when INPUT 5 is used.
*2. Except when input signal is G on SYNC or composite
SYNC
÷ When AUTO POWER OFF: ON is selected, if no sync
signal is detected for 8 minutes or more, a warning
message will be displayed for 30 seconds, after which
the display's power will switch to STANDBY mode.
5
When the setup is finished, press MENU to exit
the menu screen.
Note
The POWER MANAGEMENT and AUTO POWER OFF functions
must be set individually for each input (INPUT1-5).
To return to operating mode:
÷ To return to normal operation from POWER
MANAGEMENT mode: either operate the computer, or
press INPUT on the display or remote control unit.
÷ To return to normal operation from AUTO POWER OFF
mode: Press STANDBY/ON on the display or remote
control unit.
INPUT1
SET UP OPTION
:
L I N P UT 1
:
NT OF F
: A U T O
: V G A
CHANGE EXIT
MENU
INPUT2
SET UP OPTION
:
B E L I N P UT 2
:
O F F O F F
: A U T O
: V G A
3 OFF
ON 2