System Sensor 7100XE FAAST Installations- Und Wartungsanweisungen Seite 3

FIGURE 3. POWER AND ALARM CONNECTION BLOCK
TABLE 1. TERMINAL DESIGNATIONS
TERMINAL
BLOCK
T1
External Power – Powers Aspirating Smoke Detector
T2
Fire2 Relay – Maintains state on loss of power
T3
Fire1 Relay – Maintains state on loss of power
T4
Alert Relay – Maintains state on loss of power
T5
Fault Relay – Resets on loss of power
T6
External Monitor – Maintains state on loss of power
T7
Isolate Relay – Maintains state on loss of power
T8
RS 485 Rx
Rx and Tx can be wired in a half duplex configuration
T9
RS 485 Tx
Rx and Tx can be wired in a half duplex configuration
T10
Unused
SYSTEM WIRING
To maintain compliance with EN54-20, the power supply used with FAAST
XS must be EN54-4 approved. The system requires an EMI line filter in order
to meet CE certification to CISPR22 specifications. The EMI line filter (in-
cluded) needs to be connected between the DC power supply and the FAAST
device. The EMI filter needs to be located within the wiring compartment of
the FAAST XS unit. Refer to Figure 4 for the proper electrical connections to
the unit. Refer to Table 1 for the field wiring terminal descriptions of the unit.
Refer to Figure 4 for a typical connection for monitoring the FAAST XS system
at a Fire Alarm Control Panel (FACP).
FIGURE 4. FACP WIRING DIAGRAM
Red
Yellow (not connected)
Blue
ASP128-00
SYSTEM POWERING
The following procedure describes how to initially power up the FAAST XS system.
1. Unplug the unit's power connector to the unit before turning on the power.
2. Turn on the power.
3. Check the voltage at the connector. Make sure it is within the required volt-
age range.
4. If wiring is not connected to the external monitor terminal, install a 47kΩ
resistor (provided with the unit) into the terminal block and fit it into the T6
terminal. Remove spade connectors before installing in the wiring terminal.
5. If the voltage is within the proper range, reconnect the power connector to
the unit.
6. Connect a computer, with PipeIQ installed, to the unit using either the USB
connection, or the Ethernet port located inside the wiring compartment of
the unit. (See the 'Connecting to FAAST XS' for detailed connection instruc-
tions.)
7. Use the PipeIQ software to set up the unit configuration required for the
particular application.
8. The PC may now be disconnected unless a permanent networked connec-
tion is desired.
9. Verify the system fan starts up and air begins to flow out of the exhaust
port. The user interface will provide the device status.
10. The device will establish an airflow baseline during the first five
minutes of operation after powering on, following the successful
download of a configuration to the device from PipeIQ, or after ini-
tiating Baseline Reset from Functions menu on the unit's display.
During the initial baseline period the LCD will display Baseline message.
3
Fire Panel (FACP) typical connection
for monitoring of device
Alarm
Short = Fire
Open = Fault
Alarm
Short = Fire
Open = Fault
FACP
Alarm
Short = Fire
Open = Fault
Supervisory
Short = Isolate
Open = Fault
Supervisory
Short = Fault
Open = Normal
N.O.
Panel
N.C.
Remote
47k
Reset
C.
(Reset)
EMI Line Filter
(included)
FAAST XS
Fire Alarm Aspiration Sensing Technology®
C.
N.C.
EOL
N.O.
C.
N.C.
EOL
N.O.
C.
N.C.
EOL
N.O.
C.
N.C.
EOL
N.O.
C.
N.C.
EOL
N.O.
+
—
—
Red
Blue
ASP134-00
I56-0501-001
03-29