Front Panel; Rear Panel - Bose PowerSpace series Installationsanleitung

Product Details
PowerSpace P2600A/P21000A

Front Panel

q w e r
SIGNAL
POWER 1
LIMIT
PowerSpace
Versatile Power Amplifier
In/Out standby mode.
Power switch:
q
Power or fault state
Power LED:
w
indication.
Each LED operates
Input Signal LED:
e
independently.
Each LED operates
Output Limit LED:
r
independently.

Rear Panel

OUTPUT ATTENUATION
0 0
1 2
q
Output Attenuation controls: Output attenuation controls for each output. Turn the controls clockwise to decrease attenuation and
q
counter-clockwise to increase attenuation. The attenuator must be at 0 dB attenuation for the respective output to reach rated power.
Mute: Normally open or normally closed dry contacts can mute all outputs. Mute polarity can be inverted by a DIP switch.
w
Output terminal block: 4-terminal block connector for loudspeaker connections. Each channel can deliver up to 600 watts (P2600A) or
e
up to 1000 watts (P21000A) regardless of load into 4Ω, 8Ω, 70V, or 100V. Outputs can be I-Shared.
DIP switches: A bank of switches used to set amplifier configuration.
r
1. Auto Standby: If enabled (On), the amplifier goes into lower-power mode after 20 minutes without an input signal. If in lower-
power mode and an audio signal is detected, the amplifier will automatically wake and amplify audio within one second. The default
position is Off.
2. Mute Polarity: Switch mute polarity between NO (normally open) or NC (normally closed). NO is the default position.
3. Global Out: Sets the output capability to 70V or 100V for all outputs that have their DIP switch set to Hi-Z. In 70V Hi-Z mode and
Low-Z mode, 100 V and 70 V
P
4. Output 1: Select 70/100V high-impedance output (Hi-Z) or 4–8Ω low-impedance output (Low-Z) for Output 1.
5. Output 2: Select 70/100V high-impedance output (Hi-Z) or 4–8Ω low-impedance output (Low-Z) for Output 2.
6. I-Share 1 & 2: Deliver 2× channel power by combining the current of Outputs 1 & 2. While the amplifier is off or in Standby mode,
set this DIP switch to On and install the included jumper across the four-output terminals. Then wire the loudspeaker load to the
amplifier using terminals 1+ and 1– (or 2+ and 2–).
Input Select control: Dial selects if analog or AmpLink audio inputs are used. The default state is analog 1:1.
t
AmpLink ports: Input RJ-45 connector that receives up to eight digital channels from a Bose AmpLink product. The amp also supports
y
a Thru path for daisy-chaining all eight digital audio channels to up to eight other Bose AmpLink products, at a maximum distance of
10 meters between products.
CAUTION: Shielded EIA/TIA 568B straight Cat 5 cable, or equivalent, is required for proper AmpLink operation. Unshielded
cable is not supported and may cause AmpLink audio to operate improperly. Do NOT connect either RJ-45 port to an Ethernet-
based network.
Analog Input: Line-level input for balanced analog audio signals.
u
Update port: Used for firmware updates.
i
Gain/Sensitivity switch: Slide switch to set global gain/sensitivity setting to high gain (–10 dBv sensitivity), mid gain (4 dBu sensitivity),
o
or low gain (14 dBu sensitivity).
Power input: Power cord connection (IEC 60320-C14 inlet). Removing the power cord when the amplifier is on is an acceptable power-
a
down method.
4 • English
2
White (solid): Power is on
White (blinking): Unit is in standby mode
Red (solid): Power supply fault
Red (blinking): Thermal fault
Green: Signal present
Amber: Input is near clipping
Red: Input is clipping
Amber: Amplifier limiting an output
Red (both solid): Amplifier fault
Red (blinking): Outputs are muted
MUTE OUTPUT
CLASS 2
1 2
WIRING
w e
limiters are automatically loaded. In 100V Hi-Z mode, 100 V
RMS
Analog Input
0. 1:1
AmpLink Input
2. 1–2
3. 3–4
AmpLink
INPUT INPUT
SWITCH SETTINGS OFF ON
SELECT
1 AUTO STANDBY OFF ON
2 MUTE POLARITY NO NC
3 GLOBAL OUT 70V 100V
4 OUTPUT 1 HiZ LowZ
5 OUTPUT 2 HiZ LowZ
6 I-SHARE OFF ON
OUTPUTS
ERR LNK ERR
r t y
PowerSpace P2600A/P21000A/P4300A • Installation Guide
PRO.BOSE.COM
Faults Only
Power Thermal
Supply Fault
Fault*
Power Solid Blinking
LED red red
Limit — All solid
LEDs red
*Except for AC loss
If a power supply or amplifier fault cannot
be cleared, then the amplifier needs to be
replaced.
1. 1:ALL
GAIN
4. 5–6
(SENSITIVITY)
5. 7–8
HIGH MID LOW
(-10 dBV) (4 dBu) (14 dBu)
THRU
INPUT
LNK UPDATE
1 2
u i o
limiters are automatically loaded.
RMS
P2600A
Amplifier
Fault
—
All solid red
PowerSpace P2600A
Versatile Power Amplifier
100-240V ~ 50/60HZ
570W MAX
a