Makita 6207D Betriebsanleitung Seite 7

14. Disconnect tools
– Where the design permits, disconnect the tool
from its battery pack when not in use, before
servicing and when changing accessories such
as blades, bits and cutters.
15. Remove adjusting keys and wrenches
– Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool
before turning it on.
16. Avoid unintentional starting
– Do not carry the tool with a finger on the
switch.
17. Stay alert
– Watch what you are doing. Use common
sense. Do not operate the tool when you are
tired.
18. Check damaged parts
– Before further use of the tool, a guard or other
part that is damaged should be carefully
checked to determine that it will operate prop-
erly and perform its intended function. Check
for alignment of moving parts, free running of
moving parts, breakage of parts, mounting and
any other condition that may affect its opera-
tion. A guard or other part that is damaged
should be properly repaired or replaced by an
authorized service facility unless otherwise
indicated in this instruction manual. Have
defective switches replaced by an authorized
service facility. Do not use the tool if the switch
does not turn it on and off.
19. Warning
– The use of any accessory or attachment, other
than recommended in this instruction manual,
may present a risk of personal injury.
– Ensure that the battery pack is correct for the
tool.
– Ensure that the outside surface of battery pack
or tool is clean and dry before plugging into
charger.
– Ensure that batteries are charged using the
correct charger recommended by the manufac-
turer. Incorrect use may result in a risk of elec-
tric shock, overheating or leakage of corrosive
liquid from the battery.
20. Have your tool repaired by a qualified person
– This tool is constructed in accordance with the
relevant safety requirements. Repairs should
only be carried out by qualified persons using
original spare parts, otherwise this may result
in considerable danger to the user.
21. Disposal of battery
– Ensure battery is disposed of safety as
instructed by the manufacturer.
IMPORTANT SAFETY INSTRUCTIONS FOR
CHARGER & BATTERY CARTRIDGE
1. Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
2. Do not disassemble battery cartridge.
3. If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
4. If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
5. Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
6. Do not short the battery cartridge:
(1) Do not touch the terminals with any conduc-
tive material.
(2) Avoid storing battery cartridge in a container
with other metal objects such as nails, coins,
etc.
(3) Do not expose battery cartridge to water or
rain.
A battery short can cause a large current flow,
overheating, possible burns and even a break-
down.
7. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50°C (122°F).
8. Do not incinerate the battery cartridge even if it
is severely damaged or is completely worn out.
The battery cartridge can explode in a fire.
9. Be careful not to drop or strike battery.
SAVE THESE INSTRUCTIONS.
Tips for maintaining maximum battery life
1. Charge the battery cartridge before completely
discharged.
Always stop tool operation and charge the bat-
tery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room tempera-
ture at 10°C – 40°C (50°F – 104°F). Let a hot bat-
tery cartridge cool down before charging it.
4. Charge the Nickel Metal Hydride battery car-
tridge when you do not use it for more than six
months.
ENC004-1
7