Tyre Pressure; Changing Engine Oil - Stiga Park Ranger Gebrauchsanweisung

Servicing carried out at an authorised workshop
guarantees professional work using genuine spare
parts.
At each basic service and intermediate service car-
ried out at an authorised workshop, the service log
is stamped. A service log presenting these services
is a valuable document that improves the ma-
chine's second-hand value.
5.2 Preparation
All service and all maintenance must be carried out
on a stationary machine with the engine switched
off.
Prevent the machine from rolling by al-
ways applying the parking brake.
Stop the engine.
Prevent unintentional starting of the
engine by disconnecting the spark plug
cable(s) from the spark plug(s) and re-
moving the ignition key.

5.3 Tyre pressure

Adjust the air pressure in the tyres as follows:
Front: 0.6 bar (9 psi).
Rear: 0.4 bar (6 psi).

5.4 Changing engine oil

This section contains tables covering the different
engines that are included in STIGA's Pro range. To
facilitate reading, mark the data that applies to the
relevant machine/engine.
5.4.1 Change intervals
The table below states hours of operation and cal-
endar months. Carry out the relevant action at
whichever occurs first.
1st time
Machine
Ranger, President, Hours of operation/
(B&S) Calendar months
Changing the oil
5 hours
Excellent (B&S) Hours of operation/
Calendar months
Changing the oil
5 hours
Changing the filter
Change the oil more frequently if the engine has to
operate in demanding conditions or if the ambient
temperature is high.
ENGLISH
5.4.2 Engine Oil
Use oil according to the table below.
Oil
Service class
Use oil without any additives.
Do not fill with too much oil. This can cause the
engine to overheat.
Change oil when the engine is warm.
The engine oil may be very hot if it is
drained off directly after the engine is
shut off. Therefore allow the engine to
cool a few minutes before draining the
oil.
1. Attach the clamp on the oil drainage hose. Use
a polygrip or similar. See fig. 15-17:Y.
2. Move the clamp up 3-4 cm on the oil drainage
hose and pull out the plug.
3. Collect the oil in a collection vessel.
NOTE! Do not spill any oil on the drive belts.
4. Hand in the oil for disposal in accordance with
local provisions.
5. Install the oil drainage plug and move the clamp
back so that it clamps above the plug.
6. Remove the dipstick and fill with new oil.
Oil quantity:
Machine
Ranger
President
Excellent
7. After filling up the oil, start the engine and idle
for 30 seconds.
8. Check to see if there is any oil leakage.
Then at
9. Stop the engine. Wait for 30 seconds and then
intervals of
check the oil level in accordance with 4.2.
5.4.3 Oil filter (Excellent)
The oil filter must be replaced during every second
50 hours/
oil change, i.e. after 100 hours of operation. First
12 months
drain the engine oil and install the oil drainage plug
as described above. Then replace the oil filter as
follows:
50 hours/
1. Clean the area around the filter and dismantle
12 months
the filter.
100 hours
2. Moisten the new filter's gasket with oil.
3. Install the filter. First screw in the filter so that
the gasket comes into contact with the engine.
Then screw in the filter a further 1/2-3/4 turn.
4. Continue with point 7 in accordance with 5.4.2
Engine Oil above.
SAE 10W-30
SJ or higher
Oil volume, approx.
No filter Filter replace-
replacement ment
- 1,6 liter
- 1,6 liter
1,6 liter 1,7 liter
EN
59