Operation; Maintenance - Makita 9227CB Betriebsanleitung

To remove the wool pad, just tear it off the backing pad.
Then unscrew the backing pad while pressing the shaft
lock.
Installing or removing abrasive disc
NOTE:
• Use sander accessories specified in this manual.
These must be purchased separately.
Mount the rubber pad onto the spindle. Fit the abrasive
disc on the rubber pad and screw the lock nut onto the
spindle. (Fig. 8)
To tighten the lock nut, press the shaft lock firmly so that
the spindle cannot revolve, then use the lock nut wrench
and securely tighten clockwise.
To remove the disc, follow the installation procedure in
reverse. (Fig. 9)

OPERATION

Polishing operation (Fig. 10)
CAUTION:
• Always wear safety glasses or a face shield during
operation.
Hold the tool firmly. Turn the tool on and then apply the
wool bonnet to the workpiece.
In general, keep the wool bonnet at an angle of about
15 degrees to the workpiece surface.
Apply slight pressure only. Excessive pressure will result
in poor performance and premature wear to wool bonnet.
Sanding operation (Fig. 11)
CAUTION:
• Always wear safety goggles or a face shield during
operation.
• Never switch on the tool when it is in contact with the
workpiece, it may cause an injury to operator.
• Never run the tool without the abrasive disc. You may
seriously damage the pad.
Hold the tool firmly. Turn the tool on and then apply the
abrasive disc to the workpiece.
In general, keep the abrasive disc at an angle of about
15 degrees to the workpiece surface.
Apply slight pressure only. Excessive pressure will result
in poor performance and premature wear to abrasive disc.

MAINTENANCE

CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
Replacing carbon brushes
Remove and check the carbon brushes regularly. Replace
when they wear down to the limit mark. Keep the carbon
brushes clean and free to slip in the holders. Both carbon
brushes should be replaced at the same time. Use only
identical carbon brushes. (Fig. 12)
Use a screwdriver to remove the brush holder caps. Take
out the worn carbon brushes, insert the new ones and
secure the brush holder caps. (Fig. 13)
To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be per-
formed by Makita Authorized Service Centers, always
using Makita replacement parts.
ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita service center.
• Sponge pad (Hook & loop)
• Backing pad 165 (Hook & loop)
• Abrasive discs
• Wool bonnet 180
• Rubber pad 170
• Lock nut 48
• Lock nut wrench 28
• Sleeve 18
• Side grip (auxiliary handle)
• Loop handle
• Head cover
• Wool pad 180 (Hook & loop)
For European countries only
Noise and Vibration
The typical A-weighted sound pressure level is 81 dB (A).
The noise level under working may exceed 85 dB (A).
- Wear ear protection. -
The typical weighted root mean square acceleration value
is not more than 2.5 m/s
EC-DECLARATION OF CONFORMITY
We declare under our sole responsibility that this product
is in compliance with the following standards of standard-
ized documents, HD400, EN50144, EN55014, EN61000
in accordance with Council Directives, 73/23/EEC,
89/336/EEC, 98/37/EC.
Yasuhiko Kanzaki CE 2005
MAKITA INTERNATIONAL EUROPE LTD.
Michigan Drive, Tongwell, Milton Keynes, Bucks MK15
8JD, ENGLAND
2
.
Director
7