Werbung
Montageanleitung
NM24A
Safety notes
Product features
Simple direct mounting
Manual override
Adjustable angle of rotation
High functional reliability
Accessories
Electrical accessories
Mechanical accessories
2
Damper actuator, Open-close, 3-point, AC/DC 24 V, 10 Nm
• Cables must not be removed from the device.
• To calculate the torque required, the specifications supplied by the damper
manufacturers concerning the cross-section, the design, the installation site and the
ventilation conditions must be observed.
• The device contains electrical and electronic components and must not be disposed
of as household refuse. All locally valid regulations and requirements must be
observed.
Simple direct mounting on the damper spindle with an universal spindle clamp,
supplied with an anti-rotation device to prevent the actuator from rotating.
Manual override with push-button possible (the gear is disengaged for as long as the
button is pressed or remains locked).
Adjustable angle of rotation with mechanical end stops.
The actuator is overload protected, requires no limit switches and automatically stops
when the end stop is reached.
Description
Auxiliary switch, add-on, 1 x SPDT
Auxiliary switch, add-on, 2 x SPDT
Feedback potentiometer 140 Ohm, add-on
Feedback potentiometer 140 Ohm, add-on, grey
Feedback potentiometer 200 Ohm, add-on
Feedback potentiometer 500 Ohm, add-on
Feedback potentiometer 500 Ohm, add-on, grey
Feedback potentiometer 1 kOhm, add-on
Feedback potentiometer 1 kOhm, add-on, grey
Feedback potentiometer 2.8 kOhm, add-on
Feedback potentiometer 2.8 kOhm, add-on, grey
Feedback potentiometer 5 kOhm, add-on
Feedback potentiometer 5 kOhm, add-on, grey
Feedback potentiometer 10 kOhm, add-on
Feedback potentiometer 10 kOhm, add-on, grey
Description
Actuator arm, for one-sided spindle clamp K-ENSA
Shaft extension 250 mm, for damper spindles Ø 8...25 mm
Angled ball joint with M8, suitable for damper crank arms KH8
Straight ball joint with M8, suitable for damper crank arms KH8
Damper crank arm, for damper spindles
Spindle clamp, one side for NM..A
Spindle clamp, one side for NM..A, SM..A
Spindle clamp, reversible for NM..A and LMQ..
Angle of rotation limiter, for K-NA
Form fit insert 8x8 mm, for NM..A
Form fit insert 10x10 mm, for NM..A / SM..A
Form fit insert 12x12 mm, for NM..A / SM..A
Form fit insert 15x15 mm
Form fit insert 16x16 mm, for NM..A / SM..A
Mounting kit for linkage operation, NM..A for flat installation
Universal mounting bracket 180 mm
Base plate extension from NM..A to NM..
Position indication for LM..A, NM..A, SM..A, GM..A
NM24A • en-gb • 2016-11-01 • subject to changes
Änderungen vorbehalten
2018-01-30
l indab | Wi r v e re i nf ache n B au
RCW-2/RCWB-2
Type
S1A
S2A
P140A
P140A GR
P200A
P500A
P500A GR
P1000A
P1000A GR
P2800A
P2800A GR
P5000A
P5000A GR
P10000A
P10000A GR
Type
AH-25
AV8-25
KG8
KG10A
KH8
K-ENMA
K-ENSA
K-NA
20334-00001
ZF8-NMA
ZF10-NSA
ZF12-NSA
ZF15-NSA
ZF16-NSA
ZG-NMA
Z-ARS180
Z-NMA
Z-PI
www.belimo.eu
19
Werbung
