Nilfisk-Advance CMAX 28ST Bedienungsanleitung Seite 19

FUNCTIONAL DESCRIPTION OF CONTROL BUTTONS: FUNCTIONAL DESCRIPTION OF CONTROL BUTTONS: FUNCTIONAL DESCRIPTION OF CONTROL BUTTONS: FUNCTIONAL DESCRIPTION OF CONTROL BUTTONS: FUNCTIONAL DESCRIPTION OF CONTROL BUTTONS:
The controls were designed with one touch operation in mind. For single pass scrubbing the user can simply depress one button and all systems
on the machine will be ready to go.
For most single-pass scrubbing operations, the operator should only need to use the left-hand two buttons on the control panel. These are the
Scrub Off and Scrub ON buttons. For this reason these buttons are outlined in bright white on the control panel while the other buttons are outlined
in gray.
Solution Button (D) - This button is used to select the mode of operation for the solution system. There are 3 modes of operation for this system. Solution Button (D) Solution Button (D) Solution Button (D) Solution Button (D)
The modes are OFF, AUTO, MOMENTARY ON. Following is a description of each mode and how they are selected.
OFF MODE: OFF MODE: OFF MODE: In this mode the solution flow is turned off. As mentioned in the following, when the scrub ON button (G)
OFF MODE: OFF MODE:
will be placed in the AUTO mode. If it is desired to scrub without dispensing solution, the solution can be turned off by pressing this button at any
time.
AUTO MODE: This mode is automatically selected when the scrub ON button (G) AUTO MODE: AUTO MODE: AUTO MODE: AUTO MODE:
whenever forward or reverse direction is selected via the Drive Paddle (3)
MOMENTARY ON MODE: This mode can only be selected when the scrub mode is OFF. Solution can be dispensed by pressing and holding the MOMENTARY ON MODE: MOMENTARY ON MODE: MOMENTARY ON MODE: MOMENTARY ON MODE:
solution button. Solution will be dispensed for as long as the button is held. This is for pre-wetting the floor prior to scrubbing.
Vacuum Button Vacuum Button (E) Vacuum Button (E) (E) (E) - This button is used to select the mode of operation for the vacuum system. There are 3 modes of operation for this system.
Vacuum Button Vacuum Button (E)
These modes are OFF, AUTO, ON. Following is a description of each mode and how they are selected.
OFF MODE: OFF MODE:
OFF MODE: In this mode the vacuum is off. As mentioned in the following, when the scrub ON button (G) OFF MODE: OFF MODE:
placed in the AUTO mode. If it is desired to double-scrub (scrub without recovering the solution) the vacuum system can be turned off by pressing
this button at any time.
AUTO MODE: AUTO MODE: This mode is automatically selected when the scrub ON button (G) AUTO MODE:
AUTO MODE: AUTO MODE:
is moved forward or reverse. Once the scrub system has been turned OFF, the vacuum will remain ON. To turn the vacuum OFF, press and release
the vacuum button or the scrub OFF button (H)
independently of the scrub mode by pressing and releasing the vacuum button.
ON MODE: ON MODE: ON MODE: ON MODE: In this mode the vacuum will be on regardless of the drive paddle (3) ON MODE:
Button (E) (E) (E) (E) for approximately 1.5 seconds. The vacuum mode must first be OFF before entering this mode . This mode is included in the event an (E)
external wand is to be used with this machine or if the operator wants to clean the squeegee using the vacuum hose.
Scrub ON / Pressure Increase Button (G) - Pressing the scrub ON button will enable the scrub system and set the scrub pressure to the last Scrub ON / Pressure Increase Button (G) Scrub ON / Pressure Increase Button (G)
Scrub ON / Pressure Increase Button (G) Scrub ON / Pressure Increase Button (G)
selected value. The status display (A)
button will step the pad pressure setting through the allowable range up to the maximum value of 9. The following will occur when this button is
pressed:
• The scrub deck will be lowered
• The vacuum and solution systems will be enabled (vacuum and solution modes = AUTO)
• As soon as a direction is commanded by the Drive Paddle (3)
will turn on.
Scrub Off / Pressure Decrease Button Scrub Off / Pressure Decrease Button Scrub Off / Pressure Decrease Button (H) Scrub Off / Pressure Decrease Button Scrub Off / Pressure Decrease Button
and holding this button for approximately 1/2 second when the unit is in scrub mode will cause the following to occur:
• The status display (A) (A) (A) (A) will indicate "0"
(A)
• The scrub brushes will turn off
• The scrub deck will raise to the UP position
• The solution flow will be stopped and the last used pad pressure will be saved
• The first time that this button is pressed, the vacuum system will NOT be turned off. This is so that any remaining water may be picked up
without having to turn the vacuum back on. If this button is pressed a second time (pressed after the scrub mode has been turned off) the
vacuum will shut off after a 10 second delay.
NOTE: NOTE:
NOTE: NOTE: Reducing the pad pressure to "1" and then pressing this button one more time will also turn the scrub system OFF. In this case the last NOTE:
used pressure will not be saved.
NOTE: NOTE: NOTE: NOTE: If the optional Brush Remove Feature is installed, it functions as follows: NOTE:
• To activate the automatic brush removal feature, the scrub deck must be in the UP position and the Drive paddle must be in neutral.
• Press and hold the Scrub OFF / Pressure Decrease Button (H)
will turn on briefly. The motors will then stop abruptly which will cause the brushes to fall off.
FORM NO. 56041519 - CMAX
(H) (H)
(H) (H). This will start a ten second delay to allow pick-up of remaining solution. This mode can be selected
(A) will display the scrub pressure setting. This is indicated by a number. Subsequent presses of the scrub ON (A) (A) (A)
(3) (forward or reverse) the brushes will start turning and the vacuum and solution (3) (3) (3)
(H) (H) (H) (H) - Momentarily pressing this button will step the pad pressure down to a minimum value of 1. Pressing
(H) for 1 second. The Scrub OFF Indicator (I) (I) (I) (I) (I) will turn RED and the brush motors (H) (H) (H)
™ 28ST, 34ST / I-MAX 28C, 32C / BA 750ST, 750C / BA 850ST - 19 19 19 19 19
(G) (G) (G) is pushed. In this mode the solution flow will be turned on (G)
(3) (3)
(3). The solution flow will be turned off otherwise. (3)
(G) (G)
(G) (G) is pushed, the vacuum system will be
(G) is pushed. The vacuum will turn on when the drive paddle (3) (G) (G)
(G)
(3) (3) (3) (3) position. This mode is selected by pressing and holding the Vacuum
(G) is pushed, the solution system (G) (G)
(G)
(3) (3) (3)
(3)