Siemens SIWAREX CS Handbuch Seite 65

Programmieren in SIMATIC STEP 7
60.0 10.0 b_SIGNAL_RANGE
61.0 11.0 b_FILT_TYPE
62.0 12.0 b_FILT_FREQ
63.0 13.0 b_FILT_DEPTH
64.0 14.0 s_SCALE_ID
76.0 26.0 i_MIN_WR
78.0 28.0 i_MAX_WR
80.0 30.0 i_INCREMENT_WR
82.0 32.0 i_WEIGHT_ST_STILL
84.0 34.0 t_TIME_ST_STILL1
88.0 38.0 b_DEC_POINT
89.0 39.0 b_ZERO_NEG_VALUE
90.0 40.0 b_ZERO_POS_VALUE
91.0 41.0 b_TARA_MAX
92.0 42.0 i_Reserve
94.0 44.0 s_LEGAL_TRADE
100.0 50 s_WEGHT_UNIT
=56
106.0 s_LIMIT_PARA
106.0 0.0 i_LIMIT1_ON
108.0 2.0 i_LIMIT1_OFF
110.0 4.0 i_LIMIT2_ON
112.0 6.0 i_LIMIT2_OFF
114.0 8.0 bo_LIMIT1_PARA
114.1 8.1 bo_LIMIT2_PARA
115.0 9.0 b_Reserve
=10
116.0 s_MODUL_INFO_DATA
116.0 0.0 s_MODUL_NAME
128.0 12.0 s_ORDER_NUM
150.0 34.0 w_VERSION_HW
152.0 36.0 s_VERSION_FW
158.0 42.0 w_CRC_CHECK
=44
160.0 s_TARE_CONTROL
160.0 0.0 i_TARE_VALUE
=2
162.0 s_INTERNAL_PROC_VAL
162.0 0.0 w_CRC_CHECK
164.0 2.0 b_Reserve
165.0 3.0 bo_PRESET_TARA
166.0 4.0 d_TARA_X_100
170.0 8.0 d_ZERO_X_100
=12
174.0 s_PROCESS_VALUES
174.0 0.0 w_CRC_CHECK
SIWAREX CS 8-57
BYTE B#16#2
BYTE B#16#0
BYTE B#16#4
BYTE B#16#F
STRING[10] 'SIWAREX XX' Scale identity
INT 20
INT 2000
INT 1
INT 10
TIME T#1S
BYTE B#16#2
BYTE B#16#1
BYTE B#16#3
BYTE B#16#64
INT 0
STRING[4] '----'
STRING[4] 'kg '
END_STRUCT
STRUCT
INT 400
INT 220
INT 1000
INT 980
BOOL FALSE
BOOL FALSE
BYTE B#16#0
END_STRUCT
STRUCT
STRING[10] ''
STRING[20] ''
WORD W#16#0
STRING[4] ‚'
WORD W#16#0
END_STRUCT
STRUCT
INT 0
END_STRUCT
STRUCT
WORD W#16#0
BYTE B#16#0
BOOL FALSE
DINT L#0
DINT L#0
END_STRUCT
STRUCT
WORD W#16#0
Input range (1=1mV/v, 2=2mV/V, 4=4mV/V)
Filter type signal filter (only 0 allowed)
Filter low pass frequency
Filter depth of average value filter (0...FF)
Minimum for weighing range WR
Maximum for weighing range WR
Digital increment for weighing range
Stand still weight
Stand still time in ms
Decimal point for remote display
Zeroing negative range (% of WR)
Zeroing positive range (% of WR)
Tara range (% of WR)
Reserve
OIML or no ----
Unit for weight
DR4: Limit parameters
Value for limit 1 on
Value for limit 1 off
Value for limit 2 on
Value for limit 2 off
Limit 1 based on gross weight (0) or net
weight (1)
Limit 2 based on gross weight (0) or net
weight (1)
DR9: Module information data
Name of the module
Order number (MLFB)
Hardware version
Firmware version
CRC checksum of the application software
DR15: Tare control
Tare set value
DR26: Internal process values
CRC checksum of the application software
Tare value is preset
Actual tare value x 100
Actual zero value x 100
DR30: Process values
CRC checksum of the application software