Assembly; Preparation; Required Tools; Assembling The Grill - tepro Fremont Aufbau- Und Bedienungsanleitung

Attention Risk of damage!
The screwed connections may gradually loosen during
use and affect the stability of the grill.
– Before you use the unit, always check to make sure the screws are
secure.
– If applicable, tighten all screws again to ensure that the grill is stable.
Attention Risk of damage!
Improper handling of the grill may result in damages.
– Do not use any strong or abrasive solvents or scouring pads as they
may attack and scratch the surfaces.
– Protect the gas regulators from being contaminated by oil or mud etc.
– Once you have connected the gas hose to the container valve, do
not turn the pressure regulator any further (risk of a gas leak around
the gasket).
– If the pressure regulator is used normally, it must be replaced with a
new one no later than 10 years after the date of manufacture. Only in
this way, can proper functioning be ensured.
50
92221 LB2 innen 20121121.indb 50 92221 LB2 innen 20121121.indb 50
GB

Assembly

Preparation

Danger Risk of injury!
Failure to observe the instructions may result in problems and
risks when using the grill.
– If applicable, wear safety gloves to protect against sharp edges.
– Always follow all assembly instructions provided.
1. First completely read through the assembly instructions.
2. If necessary, have another person assist you.
3. Take enough time for the assembly and clear a work area of two to
three square meters.
4. Arrange the required tools so that they are within reach. Small parts
such as handles may be premounted.

Required tools

– Cross-slotted screwdriver
– Pliers or
• 10 mm wrench / socket key for M6 nuts
• 8 mm wrench / socket key for M5 nuts
• 7 mm wrench / socket key for M4 nuts
– 1 x 17-size open-end wrench
(national specifications may require the use of another correspond-
ing open-end wrench)

Assembling the grill

Assemble the grill as shown in figures A - Z.
Please observe the following assembly notes:
– Regarding fig. A and B: Please observe the stickers and Velcro
strips on the legs. The Velcro strips must be facing inward.
– Regarding fig. D: Please observe the stickers and make sure that the
threaded holes are facing inward.
Insert the rear screws so that the screw head is on the inside. Other-
wise the side table (9) could bump up against the protruding screw
when folded down.
– Regarding fig. G: Tighten the screws so that the burner housing (7)
is flush with the support (25/8).
– Regarding fig. H: Insert the burner (5) so that the nozzles of the tem-
perature controls extend into the burner connecting tubes. The tube
ends rest loosely above the nozzles. This gap is desired!
– Regarding fig. O: Depending on national specifications, there are
various possibilities for connecting the gas hose (20) to the grill (fig.
O only shows one example for connecting the pressure regulator).
First take the protective cap off of the gas connection (19), if present,
and dispose of it.
Method 1: Screw one end of the gas hose (20) onto the gas connec-
tion until tight (left-hand thread). Do not use an extra gasket! Hold the
gas connection firmly with pliers or an open-end wrench and then use
an open-end wrench to tighten the union nut of the gas hose.
Method 2: Slide a hose clamp of the right size a few centimetres over
the loose end of the gas hose (20).
Then slide this end onto the gas connection (19) (wet the gas connec-
tion somewhat to facilitate sliding onto the hose). Fix the connection
with the hose clamp.
Connect the other end of the gas hose (20) with the included pressure
regulator (21).
–
S
A
–
1.
2.
3.
4.
5.
6.
C
Yo
bu
No
th
–
–
–
1.
2.
3.
26.11.12 16:12 26.11.12 16:12