EGO STX3800 Bedienungsanleitung Seite 9

◾
The distance between the machine and bystanders shall
be at least 15m.
◾
Never operate the machine while the operator is tried, ill
or under the influence of alcohol or other drugs.
OPERATION
◾
Use the machine only in daylight or good artificial light.
◾
Never operate the machine with damaged guards or
shields or without guards or shields in place.
◾
Switch on the motor only when the hands and feet are
away from the cutting means.
◾
Always disconnect the machine from the power supply
(i.e. remove the battery pack).
◾
whenever leaving the machine unattended;
◾
before clearing a blockage;
◾
before checking, cleaning or working on the
machine.
◾
after striking a foreign object;
◾
whenever the machine starts vibrating abnormally.
◾
Take care against injury to feet and hands from the
cutting means.
◾
Always ensure that the ventilation openings are kept
clear of debris.
MAINTENACE AND STORAGE
◾
Disconnect the machine from the power supply
(i.e. remove the battery pack) before carrying out
maintenance or cleaning work.
◾
Use only the manufacturer's recommended
replacement parts and accessories.
◾
Inspect and maintain the machine regularly. Have the
machine repaired only by an authorized repairer.
◾
When not in use, store the machine out of the reach
of children.
OTHER SAFETY WARNINGS
◾
Avoid Dangerous Environments – Don't use
appliances on damp or wet slope.
◾
Keep guards in place and in working order.
◾
Keep hands and feet away from the cutting area.
◾
To reduce the risk of injury, never work on a ladder
or on any other insecure support. Never hold the
cutting unit above waist height.
◾
Check the cutting unit at regular short intervals
during operation, or immediately if there is a
noticeable change in cutting behavior.
◾
For best results, your battery should be charged in
a location where the temperature is greater than
5° C and less than 40° C. Do not store it outside or
in vehicles.
◾
If you are approached, stop the motor and cutting
unit.
◾
Warn the operator of the danger of blade thrust
(only using with 3-teeth blade).
◾
Blade thrust may occur when the spinning blade
contacts an object that it does not immediately cut.
◾
Blade thrust can be violent enough to cause the unit
and/or operator to be propelled in any direction, and
possibly lose control of the unit.
◾
Blade thrust can occur without warning if the blade
snags, stalls or binds.
◾
Blade thrust is more likely to occur in areas where it
is difficult to see the material being cut.
◾
Do not attach any blade to a unit without proper
installation of all required parts. Failure to use the
proper parts can cause the blade to fly off and
seriously injure the operator and/or bystanders.
Discard blades that are bent, warped, cracked,
broken, or damaged in any way. Use a sharp blade
A dull blade is more likely to snag and thrust (only
using with 3-teeth blade).
◾
A coasting blade/line can cause injury while it
continues to spin after the motor is stopped or
trigger is released. Maintain proper control until
the blade/line has completely stopped rotating.
◾
Use only with EGO's battery packs and chargers listed
below:
BATTERY PACK
BAX1500
◾
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
even when the tool is not operating. Take care when
performing maintenance or service.
◾
Do not wash with a hose; avoid getting water in
motor and electrical connections.
◾
If situations occur that are not covered in this
manual, use care and good judgment. Contact the
EGO Customer Service Center for assistance.
SAVE THESE INSTRUCTIONS!
56 VOLT LITHIUM-ION CORDLESS LINE TRIMMER — STX3800
CHARGER
CHX5500E
9
EN