Nolan N70-2 GT Sicherheit Und Gebrauchsanleitung Seite 24

N70-2 GT
2 ASSEMBLING THE INNER COMFORT PADDING
2.1 Insert the liner correctly into the helmet and fit it well against the base.
2.2 Insert the chin strap band into the corresponding slot in the liner at the area of the
cheek pads (Fig.22). Follow the previous operations on the right side of the helmet.
2.3 Insert the right and left side flaps of the liner pushing them into the cavities be-
tween the inner polystyrene cheek pads and the outer shell (Fig.21).
2.4 Insert the left front flap of the liner into the corresponding seat present on the
support fixed to the polystyrene inner shell and push it downwards until it is com-
pletely hooked. Repeat the operation with the central and right flap too (Fig.20).
Warning: check the correct assembly of the liner front area by lifting and lowering
the VPS whose movement should be unhindered. Otherwise, repeat operations
1.4 and 2.4.
2.5 Insert the right, central and left rear flaps of the liner into the corresponding seats
of the shell edge (Fig.19). Push the flaps until they are fully hooked onto the sup-
port.
2.6 Hook the roll neck left eyelet to the left frame (Fig.18), ensuring that the frame
central hole remains unhindered. Repeat the same operation on the right side of
the helmet.
2.7 Push the cheek pad padding at the snap fastener located on the rear part thereof
by fastening it to the hooking seat of the frame fixed to the shell (Fig.17), then at-
tach the left front flap of the roll neck to the cheek pad. Repeat the same operation
on the right side of the helmet.
3 DISASSEMBLING THE ROLL NECK
To disassemble the roll neck, lift the VPS, open the visor completely and remove the
chin guard from the helmet (see instructions above).
3.1 Open the chin strap (see specific instructions), remove the left front roll neck flap
from the cheek pad; pull the front part of the left cheek pad towards the inside of
the helmet to release the snap fastener located on the left frame (Fig.17). Repeat
the same operation on the right side of the helmet.
3.2 Release the roll neck left eyelet from the left frame (Fig.18). Repeat the same op-
eration on the right side of the helmet.
3.3 Release the left rear flap of the liner from the shell edge by slightly puling the com-
fort padding towards the inside of the helmet (Fig.19). Then repeat the operation
with the central flaps and with the right flap too.
3.4 Remove the roll neck from the liner by using its left, central and right slots (Fig.23).
3.5 Insert the right, central and left rear flaps of the liner into the corresponding seats
of the shell edge (Fig.19). Push the flaps until they are fully hooked onto the sup-
port.
Warning: ensure that the right and left side flaps of the liner are positioned cor-
rectly in the cavities present between the inner polystyrene cheek pads and the
outer shell (Fig.21). Otherwise, repeat operations 1.5 and 2.3.
3.6 Push the padding of the cheek pad at the snap fastener located at the rear part
thereof by hooking it to the hooking seat of the frame fixed to the shell (Fig.17).
Repeat the same operation on the right side of the helmet.
24
INSTRUCTIONS FOR USE
4 ASSEMBLING THE ROLL NECK
4.1 Open the chin strap (see specific inst
cheek pad towards the inside of the h
left frame (Fig.17). Repeat the same op
4.2 Release the left rear flap of the liner fro
fort padding towards the inside of the
with the central flaps and with the righ
4.3 Insert the roll neck into the liner by usin
4.4 Insert the right, central and left rear fla
of the shell edge (Fig.19). Push the fla
port.
Warning: ensure that the right and lef
rectly in the cavities present between
outer shell (Fig.21). Otherwise, repeat o
4.5 Hook the roll neck left eyelet to the l
central hole remains unhindered. Repe
the helmet.
4.6 Push the cheek pad padding at the sn
by fastening it to the hooking seat of t
tach the left front flap of the roll neck to
on the right side of the helmet.
WARNING
- Remove the inner comfort padding on
- Do not use the helmet before correctly
its cheek pads with the expanding foa
- Carefully wash by hand and use neutra
- Rinse using cold water and dry at room
- Do not wash the inner comfort padding
- The inner polystyrene is an easily defo
partially destroyed to help absorb shoc
- Do not modify or alter the internal pol
way.
- Clean the inner polystyrene componen
dry at room temperature away from dir
- Do not use tools and equipment to car
5 ADJUSTING THE ROLL NECK STRET
The stretch of the roll neck can be adjusted
morphology of the users and the various rid
5.1 To increase the roll neck stretch, press
taneously pull the elastic strap toward
repeat the operations on the other side
5.2 To decrease the roll neck stretch, pres
ously push the rear part of the roll nec
(Fig.25). Then repeat the operations on