Nolan N70-2 GT Sicherheit Und Gebrauchsanleitung Seite 20

N70-2 GT
2.2 Insert the external part "B" of the visor air intake in the hole provided in the visor
and engage from inside the air diffuser "A" by applying pressure to the two side
centring and hooking pins (Fig.10).
2.3 Fix the visor onto the helmet (see instructions above).
WARNING
- Ensure that the side inserts have been correctly assembled. Open and close the
visor ensuring that the side inserts remain in their positions. If necessary, repeat
the above-mentioned operations.
- Ensure that the air intake is securely fastened to the visor by opening and closing
the outer flap. If necessary, repeat the above-mentioned operations.
- Do not use the helmet without having assembled the side inserts and air intake of
the visor correctly.
- In case of malfunctioning or damages, please contact an authorised Nolangroup
dealer.
(Available as standard or accessory/spare part)
1 ASSEMBLING THE PINLOCK
1.1 Disassemble the visor (see instructions above).
1.2 Make sure that the inner surface of the visor is clean and ensure that the pin ad-
justment external levers are turned inwards (Fig.11).
1.3 Place the PINLOCK inner visor on the visor.
®
The silicone-sealed profile of the PINLOCK
the inner surface of the visor.
1.4 Insert one side of the PINLOCK
position (Fig.12).
1.5 Widen the visor and fit the second side of the PINLOCK
pin (Fig.13).
1.6 Release the visor.
1.7 Remove the protective film from the PINLOCK
entire silicone-sealed profile of the inner visor adheres to the visor.
1.8 Fix the visor onto the helmet (see instructions above).
2 CHECKING AND ADJUSTING THE PINLOCK
Check for the correct assembly of the PINLOCK
visor and ensuring that they do not move with respect to each other.
Should the PINLOCK ® inner visor not be tightly fixed to the visor, simultaneously move
both external adjustment levers upwards, to increase the stretch gradually and not
excessively (Fig.11).
The maximum stretch is achieved when the pin adjustment external levers are turned
outwards.
WARNING
- The presence of dust between the two visors may produce scratches on both
surfaces.
20
INSTRUCTIONS FOR USE
INNER VISOR
®
inner visor must be in contact with
®
inner visor into one of the visor pins and hold it in
®
inner visor to the other
®
inner visor and check that the
®
INNER VISOR STRETCH
®
inner visor by opening and closing the
®
- Scratched PINLOCK visors and inne
®
must therefore be replaced.
- Regularly check the correct stretch of
moving and scratching both surfaces.
- If the helmet visor fogs up and/or cond
that the PINLOCK inner visor is both
®
- An excessive and early stretch of the
sive adherence against the visor sur
subsequent inability to correctly perfor
- Intense sweating/breathing, the use un
peratures, high humidity, sudden chan
and prolonged use may affect the per
cause fogging or formation of conden
tem efficiency after using the helmet,
helmet visor and let it dry with dry an
applied to the helmet, in order to dry
consequence of the conditions describ
3 DISASSEMBLING THE PINLOCK
3.1 Remove the visor equipped with the
above).
3.2 Widen the visor and release the PINLO
3.3 Release the visor.
4 MAINTENANCE AND CLEANING OF T
4.1 Remove the PINLOCK inner visor fro
®
gently clean it with neutral liquid soap.
4.2 Dry the visor with dry and warm air wit
4.3 To keep the features of the visor in go
in a ventilated and dry place with the v
sources and store it in a place away fro
4.4 Do not use solvents or chemical produ
VISION PROTECTION SYSTEM (VPS)
The exclusive inner VISION PROTECTION
bonate moulded sunscreen with scratch-r
simple and practical to use: just lower it to a
of vision. It is useful in all sorts of situation
shorter town trips.
Moreover, the innovative fastening system
the sunscreen without the need of any too
operations.
1 VPS OPERATION
The VPS mechanism allows to activate the
tially covers the visor field of vision. In this
tion is achieved.
LEXAN is a trademark of SABIC.
(*)
INN
®