Cle Ning Nd M Inten Nce - ROWENTA CITY SPACE Bedienungsanleitung

903435-01_RO24_city-space_903435-01 17/01/14 13:52 Page9
EN
4. USE
ASSEMBLING THE PARTS OF THE APPLIANCE
• Firmly place the tube (19) in the vacuum opening (9) and turn to screw on – fig.1.
•To withdraw the tube, turn in the opposite sense and pull – fig.2.
• If your vacuum cleaner is equipped with a telescopic tube* (20) : push the clamping button forward, extend
the tube to the desired length and release the button to lock the tube in place - fig. 3.
Otherwise, assemble the two tubes* (21) by turning slightly - fig. 4.
• Fit the tube extension* (22) if necessary.
• Fit the required accessory onto the end of the tube:
- For rugs and carpets: use the "all floors" nozzle (23) with the brush tucked in - fig. 5, or the turbo-brush* (27 or 28*).
- For wood and hard floors: use the "all floors" nozzle (23) with the brush pulled out (fig. 6) or, for best
results, use the parquet nozzle* directly (24).
- For corners and hard to reach spots: use the crevice tool convertible into brush (26) in the flat position.
- For upholstery and delicate surfaces: use the crevice tool convertible into brush (26) or the upholstery nozzle* (25),
or the brush integrated to the grip 19b* (depending on model).
Attention! Always switch off and disconnect your vacuum cleaner before changing any accessories.
PLUGGING AND SWITCHING ON THE APPLIANCE
• Unwind the power cord completely, plug in your vacuum cleaner (fig. 7) and press the ON/OFF pedal
(2) - fig. 8.
• Set the suction power using the manual power switch on the handle: open the regulation vent in order to
manually decrease the suction power, for example: on fragile surfaces –fig. 9.
STORAGE AND TRANSPORT OF THE APPLIANCE
• After each use, switch your vacuum cleaner off by pressing on the ON/OFF pedal (2) –fig. 8- and unplug it
–fig. 10. Store the cord by pressing on the wind pedal (3) - fig.11.
• In the vertical position, place the nozzle (23) in its storage compartment on the appliance (1b) – fig. 12.
• In the horizontal position, place the nozzle (23) in its storage compartment on the appliance (1a) – fig. 13.
•You may easily transport your vacuum cleaner by the transport handle (6).

5. CLE NING ND M INTEN NCE

Important: Always switch off and unplug your vacuum cleaner before maintenance or cleaning.
CHANGING THE BAG
•The Bag full indicator (4) indicates that the bag is full or saturated. If you notice a reduction of the efficiency
of your appliance, set the power at maximum and hold the nozzle above the ground. If the Bag full indicator
remains red, replace the bag.
• Remove the flexible hose (19) from the suction opening (9) - fig. 2.
• Open the lid (8) of your vacuum cleaner - fig.14
a) If your vacuum cleaner is equipped with a paper bag* :
• Remove the bag support (15) from the bag compartment (7) – fig.15a, then remove the paper bag (18a)
from its base (15) by sliding it through the runners - fig. 15b.
•Throw the bag in the rubbish bin -fig.15c.
• Place a new bag in the bag support (15) – fig. 15d, then place the base inside the compartment by sliding
it on the runners (16) –fig. 15e.
• Make sure the bag and the bag support are correctly positioned before closing the lid (8).
b) If your vacuum cleaner is equipped with a textile bag* :
• Remove the bag support (15) from the bag compartment (7) – fig.16a, then remove the textile bag (18b)
from its support (15) by sliding it through the runners - fig. 16b.
• Open the textile bag using the zipper -fig. 16c- then empty it above a rubbish bin – fig. 16d.
• Clean the bag with running water – fig. 16e.
• Leave the bag to dry for at least 24 hours (do not replace the bag until it is perfectly dry) – fig. 16f.
* According to model :These parts are specific to certain models
9
or they are accessories that can be purchased separately.