Zennio Z35 Benutzerhandbuch Seite 97

4 Bit
4 Bit
1 Bit
1 Bit
1 Bit
1 Byte
1 Byte
1 Bit
2 Bytes
2 Bytes
1 Byte
1 Byte
700, 706, 712, 718 1 Bit
1 Byte
701, 707, 713, 719
1 Byte
720 1 Byte
721 1 Byte
722, 751, 780, 809 1 Byte
723, 752, 781, 810 1 Bit
http://www.zennio.com
C T - - - DPT_Control_Dimming
C T - - - DPT_Control_Dimming
C T - - - DPT_Switch
C T - - - DPT_Switch
I C T - W - DPT_Switch
C T - - - DPT_SceneControl
C T - - - DPT_SceneControl
O C T R - - DPT_Alarm
C T - - - 9.xxx
C T - - - DPT_Value_2_Ucount
C T - - - DPT_Scaling
C T - - - DPT_Value_1_Ucount
C T - - - DPT_Trigger
I C - - W - DPT_Scaling
I C - - W - DPT_Scaling
I C - - W - DPT_SceneNumber
C T - - - DPT_SceneControl
O C T R - - DPT_Scaling
O C T R - - DPT_Alarm
0x0 (Stop)
0x1 (Dec. by 100%)
...
0x7 (Dec. by 1%)
[Ix] [Long Press] Darker
0x8 (Stop)
0xD (Inc. by 100%)
...
0xF (Inc. by 1%)
0x0 (Stop)
0x1 (Dec. by 100%)
...
0x7 (Dec. by 1%)
[Ix] [Long Press] Brighter/Darker
0x8 (Stop)
0xD (Inc. by 100%)
...
0xF (Inc. by 1%)
0/1 [Ix] [Long Press] Light On
0/1 [Ix] [Long Press] Light Off
0/1 [Ix] [Long Press] Light On/Off
0-63; 128-191 [Ix] [Long Press] Run Scene
0-63; 128-191 [Ix] [Long Press] Save Scene
[Ix] [Switch/Sensor] Alarm:
0/1
Breakdown or Sabotage
[Ix] [Long Press] Constant Value
-671088,64 - 670760,96
(Float)
[Ix] [Long Press] Constant Value
0 - 65535
(Integer)
[Ix] [Long Press] Constant Value
0% - 100%
(Percentage)
[Ix] [Long Press] Constant Value
0 - 255
(Integer)
[Ix] [Long Press/Release] Stopp
0/1
Shutter
[Ix] [Long Press] Dimming Status
0% - 100%
(Input)
[Ix] [Long Press] Shutter Status
0% - 100%
(Input)
0 - 63 [Motion Detector] Scene Input
0-63; 128-191 [Motion Detector] Scene Output
0% - 100% [Ix] Luminosity
0/1 [Ix] Open Circuit Error
Long Pr. -> Darker; Release ->
Stopp
Long Pr. -> Brighter/Darker;
Release -> Stop
Sending of 1 (On)
Sending of 0 (Off)
Switching 0/1
Sending of 0 - 63
Sending of 128 - 191
1 = Alarm; 0 = No Alarm
Float Value
0 - 65535
0% - 100%
0 - 255
Release -> Stopp Shutter
0% - 100%
0% = Top; 100% = Bottom
Scene Value
Scene Value
0-100%
0 = No Error; 1 = Open Circuit
Error
Techn. Support: http://support.zennio.com
Z35
97