Specific Safety Rules - Makita 6706D Betriebsanleitung

SPECIFIC SAFETY RULES

DO NOT let comfort or familiarity with product
(gained from repeated
adherence to screwdriver safety rules. If you use
this tool unsafely or incorrectly, you can suffer
serious personal injury.
1. Hold power tools by insulated gripping surfaces
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
2. Always be sure you have a firm footing. Be sure
no one is below when using the tool in high loca-
tions.
3. Hold the tool firmly.
4. Keep hands away from rotating parts.
5. Do not touch the bit or the workpiece immedi-
ately after operation; they may be extremely hot
and could burn your skin.
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated
in this instruction manual may cause serious per-
sonal injury.
OPERATING INSTRUCTIONS
Installing or removing battery cartridge (Fig. 1)
• Always switch off the tool before insertion or
removal of the battery cartridge.
• To remove the battery cartridge, pull out the set
plate on the tool and grasp both sides of the car-
tridge while withdrawing it from the tool.
• To insert the battery cartridge, align the tongue on
the battery cartridge with the groove in the housing
and slip it into place. Snap the set plate back into
place. Be sure to close the set plate fully before
using the tool.
• Do not use force when inserting the battery car-
tridge. If the cartridge does not slide in easily, it is
not being inserted correctly.
Installing or removing socket
Important:
Always be sure that the tool is switched off and the
battery cartridge is removed before installing or
removing the socket.
For tool with square drive (Fig. 2 & 3)
Use 9.5 mm square drive socket with a hole for detent
pin which is available on the market. (Note: Use
6.35 mm square drive socket when using the tool with
6.35 mm square drive.) To install the socket, depress
the detent pin on the square drive with your finger
and push the socket onto the square drive until the
detent pin is inserted into the hole in the socket. To
remove the socket, depress the detent pin with a
small hand tool and pull off the socket.
6
GEB017-1
use) replace strict
For tool with round drive (Fig. 4)
Use a bit with Form C 6.3 shank which is available on
the market. The bit can be inserted directly into the
round drive and held in place. To install the bit, push it
firmly into the round drive. To remove the bit, grasp it
with a pair of pliers and pull it out of the round drive.
Sometimes, it helps to wiggle the bit with the pliers as
you pull.
Switch action (Fig. 5)
CAUTION:
Before inserting the battery cartridge into the tool,
always check to see that the switch trigger actuates
properly and returns to the "OFF" position when
released.
To start the tool, simply pull the trigger. Release the
trigger to stop.
Reversing switch action (Fig. 5)
CAUTION:
• Always check the direction of rotation before opera-
tion.
• Use the reversing switch only after the tool comes
to a complete stop. Changing the direction of rota-
tion before the tool stops may damage the tool.
This tool has a reversing switch to change the direc-
tion of rotation. Slide the reversing switch up for
clockwise rotation or slide it down for counterclock-
wise rotation.
Overload protector
For 6704D and 6704DW
The overload protector automatically cuts out to
break the circuit whenever heavy work is prolonged.
Wait 20 – 30 seconds before resuming operation.
Adjusting the fastening torque (Fig. 6)
The fastening torque can be adjusted infinitely from
approx. 20 kg cm to 80 kg cm. To adjust it, loosen the
two screws and turn the adjusting ring. Then tighten
the screws to secure the adjusting ring. Refer to the
table below for relation between the numbers on the
adjusting ring and the fastening torque to be
obtained.
Numbers on
adjusting ring
1
2
3
4
5
(Example)
35 kg cm of fastening torque can be obtained when
the number 2 is aligned to the red mark.
Fastening torque
to be obtained
20 kg cm
35 kg cm
48 kg cm
60 kg cm
80 kg cm