JEWADO Turbothrust Saw Gebrauchsanleitung Seite 14

• in the vertical position or at an angle to use Turbothrust
Saw® for cutting freehand; or
• in the reverse position, if this will provide a more comforta-
ble and practical grip for the task at hand.
Follow the steps below to adjust the control handle.
Image G
Step Action
1
Loosen the control handle lock screw (G. 1) until
you are able to move the handle up and down.
2
Move the control handle into the desired posi-
tion.
3
Tighten the control handle lock screw.
How to Adjust the Depth Gauge
The cutting bit must always protrude from the base of the
depth gauge by 4 mm plus the thickness of the material
to be cut.
For example: if you are going to cut a piece of plasterboard
that is 10 mm thick, the cutting bit must protrude 14 mm
beneath the base of the depth gauge. In other words, once
you begin cutting, there will be 4 mm of cutting bit between
the plasterboard and the base of the depth gauge.
Follow the steps below to adjust the depth gauge.
Image H
Step Action
1
Loosen the depth gauge lock screw (H.1). Slide
the base of the depth gauge up or down to reach
the desired depth.
2
Tighten the depth gauge lock screw firmly.
3
Check the depth of the bit before starting to
cut. Make sure the bit and the chuck are firmly
tightened.
How to Attach the Circular Cutter (Image I)
Follow the steps below to attach the circular cutter.
Step Action
1
Unscrew the internal mounting disc (I.1) from
the external mounting disc (I. 2).
2
Place the internal mounting disc onto the base
of the control handle (I. 3).
3
Position the mounting hole in the circular cut-
ting guide (I. 4) over the threaded part of the
internal mounting disc (I. 1).
Note: make sure the pivot (I. 5) is pointing
downwards.
4
Attach the external mounting disc to the inter-
nal mounting disc. Tighten them by hand.
Note: make sure the protruding section (I. 6)
of the external mounting disc (I. 2) passes
through the mounting hole (I. 4) and is faste-
ned firmly in place. Only tighten it by hand. Do
not over-tighten.
5
Loosen the pivot lock screw (I. 7) and slide it
to adjust the radius of the circle, then tighten
it again.
6
Insert the appropriate cutting bit into the chuck
and tighten it. To do this, see the section How
to Attach Cutting Bits.
Note: check you have adjusted the radius of
the circle correctly by measuring the distance
from the pivot to the outside of the bit.
7
Adjust the depth gauge. To do this, see the
section How to Adjust the Depth Gauge.
How to Attach the Guide Stop (Image J)
Follow the steps below to attach the guide stop.
Step Action
1
Loosen the lock screws on the adjustable guide
stop (J.1). There are two of them, one on each
side of the base.
2
Insert the adjustable guide stop (J.2) into the
base.
3
Adjust the depth of the guide stop and tighten
the lock screws again.
How to Attach the Dust Extractor Connector (Image K)
Follow the steps below to attach the dust extractor acces-
sory.
Step Action
1
Insert the dust extractor connector into the
collar on the base, as shown in the illustration.
2
Insert your vacuum cleaner hose into the con-
nector.
Note: if the size of your hose's nozzle does not
match that of the connector, use a piece of gar-
den hose as an adaptor.
How to attach Turbothrust® Flex (Image L)
Follow the steps below to attach the Turbothrust® Flex ro-
tary attachment .
Step Action
1
Switch off your Turbothrust Saw® and unplug
it from the power supply.
2
If it has a bit attached, remove it.
3
Make sure the Ø 6.35 mm chuck is on the
spindle.
To do this, see the section How to Change
Chucks.
4
Insert the rear section of the Turbothrust Flex®
(L. 1) into the chuck (L.2).
5
When the rear section of the Turbothrust
Flex® is correctly positioned inside the chuck,
press the spindle lock button (L.3). Turn the
chuck nut (L. 4) clockwise by hand, making it
as tight as you can.
6
Use the Ø 16 mm chuck key to tighten the
chuck nut firmly, but take care NOT to apply
too much force.