Spectral CTA1-V2 Bedienungsanleitung Seite 60

Connecting SPECTRAL sound system:
To register the remote control on a (further) sound system open the Programme Menu
by pressing <exit> and <m> simultaneously. Select "RF Learn"
and confirm this with <ok> . Select "new device" to register a sound system on the
remote control.
After confirmation you will be asked to connect
the sound system to be programmed to the mains power supply and to switch it on.
Wait at least 3 sec., then confirm with <ok>.
Before doing this you should ensure that the sound system had been
disconnected from the mains power supply for at least 1 minute.
The remote control will now try to connect with the newly activated sound system.
A successful connection will be shown in the display as "Installation successful", while
failure will bring the message "Installation failed". If the connection
has failed you should identify the problem (device not switched on, distance too great,
sound system not disconnected from the mains power supply
for long enough, etc) and start the process again.
After successful installation you must enter a name for the sound system. If you enter
a name (e.g. BRA1) more than once the remote control will automatically allocate it a
subscript (e.g. BRA1.1, BRA1.2 ...). You can then exit the "RF-Learn" menu by
pressing <exit> twice.
If you wish to overwrite an existing sound system, instead of selecting "new device" you
should select the system you wish to replace and confirm your
power power
selection with <ok> . Select the "Learn" function to proceed. Confirm the overwriting
with the "yes" function key or abort the process with "no".
lighting lighting
Continue as previously described under "new device".
rgb rgb
Delete SPECTRAL sound system:
To de-register your remote control from a sound system open the Programme Menu by pressing <exit> and <m> simultaneously, select "RF Learn"
and confirm with <ok>. Select the system you wish to "delete" and confirm your selection with <ok>. Select and confirm the "Clear" function to
lan lan ua ua e e
g g g g
continue. Complete the de-registration process by pressing the "yes" function key or abort the process with "no".
english deutsch deutsch
setup setup
speaker setup speaker setup ► ►
system setup system setup ► ►
60
main key main key
blu ray blu ray
dvd dvd  ►  ►
dvd rec dvd rec
sat sat
 
tv1 tv1
 
 
IR Learn IR Learn
Programming successful Programming successful
RF Learn RF Learn
spectral bra1 spectral bra1
new device new device ► ►
english
contrast contrast
75 75
speaker set speaker set
preset preset ► ►
level trim level trim ► ►
speaker distance speaker distance ► ►
tone control tone control ► ►
bass expand bass expand bypass bypass
room comp room comp ► ►
Learn Learn ► ►
Clear Clear
Name Name
IR Learn IR Learn
Programming failed Programming failed
yes
RF Learn RF Learn
Plug in RF Device Plug in RF Device
press OK press OK
power power
lighting lighting
rgb rgb
lan lan ua ua e e
g g g g
english
deutsch deutsch
setup setup
speaker setup speaker setup ► ►
system setup system setup ► ►
preset save preset save
current value current value ► ►
default value default value ► ►
exit without save exit without save
power power
ok ok
menu(m) menu(m)
exit exit
left left
right right
 
RF Learn RF Learn
IR Learn IR Learn
spectral bra1 spectral bra1
new device new device ► ►
Clear Device Clear Device
Are you sure ? Are you sure ?
yes no no
RF Learn RF Learn
Installation successful Installation successful
RF Learn RF Learn
Installation failed Installation failed
contrast contrast
75 75
speaker set speaker set
preset preset ► ►
level trim level trim ► ►
speaker distance speaker distance ► ►
tone control tone control ► ►
bass expand bass expand bypass bypass
room comp room comp ► ►
system set system set
preset preset
output config output config ► ►
sub lineout sub lineout disabled disabled
preset p1 preset p1 default default
input config input config ► ►
preset p2 preset p2 default default
ir learn ir learn ► ►
preset p3 preset p3 default default
lip sync lip sync 0 ms 0 ms
preset p4 preset p4 default default
dynamic dynamic full full
 
preset p5 preset p5 default default
preset p6 preset p6 default default
press remote button press remote button
yes
RF Learn RF Learn
IR Learn IR Learn
Plug in RF Device Plug in RF Device
Learn Learn
press OK press OK
Clear Clear
Name Name ► ►
RF Learn RF Learn
Select Device Select Device
cla1 cla1
cta1 cta1
cta2 cta2
bra1 bra1
vra1
preset save preset save
current value current value ► ►
default value default value ► ►
exit without save exit without save
Are y Are
yes
RF R
IR I
Installa Insta
amp amp
apple tv apple tv
audio rec audio rec
beamer beamer
blue ray blue ray
cd cd
RF R
Insta Ins
p
preset p1 preset p1
preset p2 preset p2
preset p3 preset p3
preset p4 preset p4
preset p5 preset p5
preset p6 preset p6