janitza UMG 96 RM-PN Installationsanleitung Seite 14

14 Operation and button functions Operation and button functions
14
Technical data Technical data
18 18
The device is operated with buttons 1 and 2,
The device is operated with buttons 1 and 2,
whereby the following distinctions are made: whereby the following distinctions are made:
P)
General information General information
• Short press (button 1 or 2):
• Short press (button 1 or 2):
Net weight Net weight
Next step (+1). approx. 380 g
Next step (+1).
(with attached connectors) (with attached connectors)
• Long press (button 1 or 2):
• Long press (button 1 or 2):
Packaging weight Packaging weight
approx. 780 g
(including accessories) (including accessories)
previous step (-1).
previous step (-1).
Lithium battery CR2032, 3 V
Battery Battery
(approval i.a.w. UL 1642)
The device differentiates between display and
The device differentiates between display and
40000 h
programming mode.
programming mode.
(after this period of time
Service life of Service life of
the background lighting
background lighting background lighting
efficiency will reduce by
Measured values are arranged in measured value
Measured values are arranged in measured value approx. 50%)
display profiles and can be adjusted easily in the display profiles and can be adjusted easily in the
GridVis® software (included). Measured value
GridVis® software (included). Measured value
Transport and storage Transport and storage
s
display profile 1 is configured in the factory.
display profile 1 is configured in the factory.
The following information applies to devices which are trans- The following information applies to devices which are trans-
ng
ported or stored in the original packaging. ported or stored in the original packaging.
Free fall Free fall 1 m
Display mode
Display mode
• You can use buttons 1 and 2 to scroll between Temperature Temperature K55 (-25° C to +70° C)
• You can use buttons 1 and 2 to scroll between
the measured value indications.
Relative humidity Relative humidity the measured value indications. 0 to 90% RH
• The measured value indication shows up to
• The measured value indication shows up to
3 measured values. 3 measured values.
• A time for an automatic indication change
• A time for an automatic indication change
between the measured value indications can be
between the measured value indications can be
configured in the GridVis® software.
configured in the GridVis® software.
C
C
NOTE! NOTE!
More detailed information on operation, display and button functions for your device can be
More detailed information on operation, display and button functions for your device can be
found in the user manual. found in the user manual.
Digital outputs
Digital outputs
2 and 3 optional digital outputs, semiconductor relays, not 2 and 3 optional digital outputs, semiconductor relays, not
short-circuit proof.
short-circuit proof.
Switching voltage Switching voltage max. 33 V AC, 60 V DC
Switching current Switching current max. 50 mAeff AC/DC
Response time Response time 10/12 periods + 10 ms *
Pulse output (energy pulse) max. 50 Hz
Pulse output (energy pulse)
* Response time e.g. at 50 Hz: 200 ms + 10 ms = 210 ms
* Response time e.g. at 50 Hz: 200 ms + 10 ms = 210 ms
Digital inputs
Digital inputs
3 optional digital inputs, semiconductor relays,
3 optional digital inputs, semiconductor relays,
not short-circuit proof.
not short-circuit proof.
Maximum counter frequency 20 Hz
Maximum counter frequency
18V .. 28 V DC
Input signal present
Input signal present
(typical 4 mA)
0 .. 5 V DC,
Input signal not present
Input signal not present
current less than 0.5 mA
Temperature measurement input
Temperature measurement input
2 optional inputs.
2 optional inputs.
Update time Update time 1 second
PT100, PT1000, KTY83,
Connectable sensors Connectable sensors
KTY84
Total burden (sensor + cable) Total burden (sensor + cable) max. 4 kOhm
Max. value, HT/reference
Max. value, HT/reference
Min. value NT/export
Min. value NT/export
Ambient coditions during operation Ambient coditions during operation
The UMG 96RM is intended for weather-protected, stationary The UMG 96RM is intended for weather-protected, stationary
approx. 380 g
use. Protection class II i.a.w. IEC 60536 (VDE 0106, Part 1). use. Protection class II i.a.w. IEC 60536 (VDE 0106, Part 1).
approx. 780 g Operating temperature range Operating temperature range K55 (-10° C .. +55° C)
Relative humidity Relative humidity 0 to 75% RH
Lithium battery CR2032, 3 V
(approval i.a.w. UL 1642)
Operating altitude Operating altitude 0 .. 2000 m above sea level
40000 h
Degree of pollution Degree of pollution 2
(after this period of time
the background lighting
Mounting position Mounting position vertical
efficiency will reduce by
Forced ventilation is
approx. 50%)
Ventilation Ventilation
not required.
Protection against ingress Protection against ingress
of solid foreign bodies and of solid foreign bodies and
water water
- Front side - Front side IP40 i.a.w. EN60529
- Rear side - Rear side IP20 i.a.w. EN60529
- Front with seal - Front with seal IP54 i.a.w. EN60529
1 m
Export
Export
K55 (-25° C to +70° C)
Fig. Display UMG 96 RM-PN
Fig. Display UMG 96 RM-PN
0 to 90% RH
Supply voltage Supply voltage
Option 230 V:
AC 90 V - 277 V (50/60 Hz) or
DC 90 V - 250 V, 300 V CATIII
Nominal range Nominal range
Option 24 V:
AC 24 V - 90 V (50/60 Hz) or
DC 24 V - 90 V, 150 V CATIII
Operating range Operating range +-10% of the nominal range
Option 230 V: max. 8,5 VA / 5 W
Power consumption Power consumption
Option 24 V: max. 7 VA / 5 W
Internal fuse, Internal fuse, Type T1A / 250 VDC / 277 VAC
not replaceable not replaceable according to IEC 60127
Option 230 V: 6-16 A
Recommended over- Recommended over-
Option 24 V: 1-6 A
current protection device for current protection device for
(Char. B)
the line protection the line protection
(IEC/UL approval)
Serial interface
Serial interface
RS485 - Modbus RTU/Slave RS485 - Modbus RTU/Slave
max. 33 V AC, 60 V DC
Stripping length
max. 50 mAeff AC/DC Stripping length
10/12 periods + 10 ms *
max. 50 Hz
Ethernet connection
Ethernet connection
Connection
Connection
Conformance Class
Conformance Class
ProfiNet-Version
ProfiNet-Version
ProfiNet-Profile
ProfiNet-Profile
20 Hz
18V .. 28 V DC
(typical 4 mA)
0 .. 5 V DC,
Cable length (digital inputs and outputs,
Cable length (digital inputs and outputs,
current less than 0.5 mA
temperature measurement input)
temperature measurement input)
Up to 30 m Up to 30 m
More than 30 m More than 30 m
1 second
PT100, PT1000, KTY83,
KTY84
max. 4 kOhm
15 Programming mode
15
• Press and hold buttons 1 and 2 simultaneously
for 1 second to switch between display mode
Voltage measurement
Mean value
Mean value
and programming mode. The text PRG
3-phase 4-conductor systems
appears in the display.
with rated voltages of up to
Programming Programming
mode • Configure the necessary settings for the 3-phase 3-conductor
mode
K55 (-10° C .. +55° C) systems, not earthed, with
Summation
Summation
operation of the device in programming mode.
rated voltages of up to
measurement measurement
0 to 75% RH
Phase conductor - • The programming mode can be protected with Overvoltage category
Phase conductor -
0 .. 2000 m above sea level
Phase conductor
Phase conductor Rated surge voltage
a user password.
2 Protection
Password • Button 2 switches between the programming
Password
of voltage measurement
vertical CT: Current
CT: Current menus:
Metering range L-N
transformer
transformer
Forced ventilation is 1. Current transformer
VT: Voltage
VT: Voltage
not required.
Metering range L-L 2. Voltage transformer
transformer
transformer
K1: Output 1 3. Parameter list
K1: Output 1
Resolution
K2: Output 2
K2: Output 2
Crest factor 4. TCP/IP device address
IP40 i.a.w. EN60529
Impedance 5. Subnet mask
IP20 i.a.w. EN60529
Button 2
Button 2
IP54 i.a.w. EN60529
Power consumption
6. Gateway address
Button 1
Button 1
Sampling rate
The device switches from programming mode to
Frequency range of the
fundamental oscillation -
Option 230 V: display mode if
resolution
AC 90 V - 277 V (50/60 Hz) or
• no buttons are pressed for 60 seconds.
DC 90 V - 250 V, 300 V CATIII 1) ... The device determines measured values only if the Voltage
• buttons 1 and 2 are pressed simultaneously for measurement input V1 voltage L1-N greater than 20 Vrms
Option 24 V:
(4-wire measurement) or a voltage L1-L2 of larger 34 Vrms
AC 24 V - 90 V (50/60 Hz) or
1 second.
DC 24 V - 90 V, 150 V CATIII (3-wire measurement) is applied.
+-10% of the nominal range
Option 230 V: max. 8,5 VA / 5 W
Option 24 V: max. 7 VA / 5 W
C
Type T1A / 250 VDC / 277 VAC
according to IEC 60127
Option 230 V: 6-16 A
Option 24 V: 1-6 A
(Char. B)
(IEC/UL approval)
Terminal connection capacity (power supply voltage)
Conductors to be connected.
9.6 kbps, 19.2 kbps, 9.6 kbps, 19.2 kbps,
Only one conductor can be connected per terminal!
38.4 kbps, 57.6 kbps, 38.4 kbps, 57.6 kbps,
115.2 kbps Single core, multi-core,
115.2 kbps
fine-stranded
7 mm
7 mm
Terminal pins, core end sheath
Tightening torque
Stripping length
RJ45
RJ45
B - Switch class (IRT)
B - Switch class (IRT)
Terminal connection capacity (residual current or
2.2
2.2
temperature measurement inputs and digital inputs /
PROFIenergy V1.1,
PROFIenergy V1.1,
outputs)
Entity Class 2
Entity Class 2
Single core, multi-core,
fine-stranded
Terminal pins, core end sheath
Tightening torque
Stripping length
Unshielded Unshielded
Shielded Shielded
Terminal connection capacity (serial interface)
Single core, multi-core,
fine-stranded
Terminal pins, core end sheath
Tightening torque
Stripping length
14 / 16
Programming mode
C
• Press and hold buttons 1 and 2 simultaneously
for 1 second to switch between display mode
Voltage measurement Current measurement I1 - I4
and programming mode. The text PRG
3-phase 4-conductor systems Nominal current
277 V/480 V (+-10%) 277 V/480 V (+-10%)
appears in the display.
with rated voltages of up to
Metering range
3-phase 3-conductor
• Configure the necessary settings for the
systems, not earthed, with IT 480 V (+-10%) IT 480 V (+-10%) Crest factor
operation of the device in programming mode.
rated voltages of up to
Resolution
Overvoltage category 300 V CAT III 300 V CAT III
• The programming mode can be protected with
Overvoltage category
Rated surge voltage 4 kV 4 kV
a user password.
Rated surge voltage
Protection 1 - 10 A 1 - 10 A C
• Button 2 switches between the programming
of voltage measurement (with IEC-/UL approval) (with IEC-/UL approval) Power consumption
menus:
0 1) to 300 Vrms 0 1) to 300 Vrms
Overload for 1 sec.
Metering range L-N
(max. overvoltage 520 Vrms ) (max. overvoltage 520 Vrms )
1. Current transformer
0 1) to 520 Vrms 0 1) to 520 Vrms
Metering range L-L Sampling rate
2. Voltage transformer
(max. overvoltage 900 Vrms ) (max. overvoltage 900 Vrms )
3. Parameter list
Resolution 0.01 V 0.01 V
Crest factor 4. TCP/IP device address 2.45 (based on metering range) 2.45 (based on metering range)
Residual current monitoring I5 / I6
Impedance 4 MOhm / phase 4 MOhm / phase
5. Subnet mask
Nominal current
Power consumption approx. 0.1 VA approx. 0.1 VA
6. Gateway address
21.33 kHz (50 Hz), 25.6 kHz (60 Hz) 21.33 kHz (50 Hz), 25.6 kHz (60 Hz)
Metering range
Sampling rate
for each measurement channel for each measurement channel
Triggering current
The device switches from programming mode to
Frequency range of the
45 Hz to 65 Hz 45 Hz to 65 Hz
Resolution
fundamental oscillation -
display mode if
0.01 Hz 0.01 Hz
resolution
Crest factor
• no buttons are pressed for 60 seconds.
1) ... The device determines measured values only if the Voltage
Burden
measurement input V1 voltage L1-N greater than 20 Vrms
• buttons 1 and 2 are pressed simultaneously for
In order to make the following settings, sample
(4-wire measurement) or a voltage L1-L2 of larger 34 Vrms Overload for 1 sec.
1 second.
(3-wire measurement) is applied.
settings for the device and the PC are selected:
Sustained overload
Device IP address: 192.168.1.116
Overload for 20 ms
Subnet mask:
C
NOTE!
NOTE!
PC IP address:
Changes are only applied after exiting
Changes are only applied after exiting
Subnet mask:
programming mode.
programming mode.
Terminal connection capacity (power supply voltage)
Conductors to be connected.
Only one conductor can be connected per terminal!
Single core, multi-core,
0.2 - 2.5 mm , AWG 26-12
0.2 - 2.5 mm 2 2 , AWG 26-12
fine-stranded
0.2 - 2.5 mm
Terminal pins, core end sheath 0.2 - 2.5 mm 2 2
0.4 - 0.5 Nm
Tightening torque 0.4 - 0.5 Nm
7 mm
Stripping length 7 mm
Terminal connection capacity (residual current or
temperature measurement inputs and digital inputs /
outputs)
Single core, multi-core,
0.2 - 1.5 mm 0.2 - 1.5 mm 2 , AWG 28-16 , AWG 28-16
2
fine-stranded
Terminal pins, core end sheath 0.2 - 1.5 mm 0.2 - 1.5 mm 2
2
Tightening torque 0.2 - 0.25 Nm 0.2 - 0.25 Nm
7 mm
Stripping length 7 mm
Terminal connection capacity (serial interface)
Single core, multi-core,
0.2 - 1.5 mm 0.2 - 1.5 mm 2 , AWG 28-16 , AWG 28-16
2
fine-stranded
Terminal pins, core end sheath 0.2 - 1.5 mm 0.2 - 1.5 mm 2
2
0.2 - 0.25 Nm
Tightening torque 0.2 - 0.25 Nm
7 mm
Stripping length 7 mm
C
NOTE!
NOTE!
The TCP/IP device address is configured
The TCP/IP device address is configured
Current measurement I1 - I4
directly on the device (see step 17).
directly on the device (see step 17).
Nominal current 5 A 5 A
The device is also equipped with The device is also equipped with
Metering range 0 to 6 Arms 0 to 6 Arms
dynamic TCP/IP addressing (DCP) for
dynamic TCP/IP addressing (DCP) for
Crest factor 1.98 1.98
ProfiNet systems!
ProfiNet systems!
Resolution 0.1 mA (display 0.01 A) 0.1 mA (display 0.01 A)
Overvoltage category 300 V CAT II 300 V CAT II
Rated surge voltage 2 kV 2 kV
C
NOTE!
NOTE!
Power consumption approx. 0.2 VA (Ri = 5 mΩ) approx. 0.2 VA (Ri = 5 mΩ)
The following section explains the The following section explains the
Overload for 1 sec. 120 A (sinusoidal) 120 A (sinusoidal)
programming menus for the current
programming menus for the current
21.33 kHz (50 Hz), 21.33 kHz (50 Hz),
Sampling rate transformer (1.), TCP/IP device address, 25.6 kHz (60 Hz) 25.6 kHz (60 Hz)
transformer (1.), TCP/IP device address,
for each measurement channel for each measurement channel
subnet mask and gateway address (4., 5., 6.)
subnet mask and gateway address (4., 5., 6.)
via the Ethernet interface, which are most
via the Ethernet interface, which are most
Residual current monitoring I5 / I6
important for a installation manual. important for a installation manual.
Nominal current 30 mArms 30 mArms
The Dynamic Configuration Protocol
The Dynamic Configuration Protocol
Metering range 0 to 40 mArms 0 to 40 mArms
(DCP) distributes the addresses and
(DCP) distributes the addresses and
50 µA 50 µA
Triggering current
names within ProfiNet systems! names within ProfiNet systems!
Resolution 1 µA 1 µA
The UMG 96 RM-PN prioritises DCP.
The UMG 96 RM-PN prioritises DCP.
Crest factor 1.414 (related to 40 mA) 1.414 (related to 40 mA)
Burden 4 Ohm 4 Ohm
In order to make the following settings, sample Overload for 1 sec. 5 A 5 A
settings for the device and the PC are selected:
Sustained overload 1 A 1 A
Device IP address: 192.168.1.116
Overload for 20 ms 50 A 50 A
255.255.255.0
Subnet mask: 255.255.255.0
192.168.1.117
PC IP address: 192.168.1.117
Subnet mask: 255.255.255.0 255.255.255.0
Terminal connection capacity (current measurement) Terminal connection capacity (current measurement)
Conductors to be connected.
Conductors to be connected.
Only one conductor can be connected per terminal!
Only one conductor can be connected per terminal!
Single core, multi-core,
Single core, multi-core,
0.2 - 2.5 mm , AWG 26-12
0.2 - 2.5 mm 2 2 , AWG 26-12
fine-stranded
fine-stranded
Terminal pins, core end sheath 0.2 - 2.5 mm
Terminal pins, core end sheath 0.2 - 2.5 mm 2 2
Tightening torque 0.4 - 0.5 Nm
Tightening torque 0.4 - 0.5 Nm
Stripping length 7 mm
Stripping length 7 mm
Terminal connection capacity (voltage measurement)
Terminal connection capacity (voltage measurement)
Conductors to be connected.
Conductors to be connected.
Only one conductor can be connected per terminal!
Only one conductor can be connected per terminal!
Single core, multi-core,
Single core, multi-core,
0.08 - 4.0 mm 2 , AWG 28-12
0.08 - 4.0 mm 2 , AWG 28-12
fine-stranded
fine-stranded
Terminal pins, core end sheath 0.2 - 2.5 mm 2
Terminal pins, core end sheath 0.2 - 2.5 mm 2
Tightening torque 0.4 - 0.5 Nm
Tightening torque 0.4 - 0.5 Nm
Stripping length 7 mm
Stripping length 7 mm
C
C
NOTE!
NOTE!
Further technical data can be found in the
Further technical data can be found in the
user manual for the device.
user manual for the device.