Technical Data; Before Starting The Equipment - EINHELL MGE-CM 36 Li M Originalbetriebsanleitung

4. Technical data

Cutter rail length ..................................... 520 mm
Cutting length ......................................... 460 mm
Tooth spacing ........................................... 15 mm
Cuts/min ...................................................... 2200
Charging time ..................................... ca. 40 min.
Sound pressure level, L
Sound power level, L
WA
K uncertainty ................................................. 3 dB
Interchangeable battery ......18 V d.c. / 2000 mAh
.............................(optional 18 V d.c. / 1500 mAh)
.............................(optional 18 V d.c. / 3000 mAh)
.............................(optional 18 V d.c. / 4000 mAh)
.............................(optional 18 V d.c. / 5200 mAh)
......................................... ≤ 2.5 m/s²
Vibration a
hv
K uncertainty .............................................. 1.5 dB
Weight ........................................................2.0 kg
Battery charger
Mains voltage ....................200-250 V ~ 50-60 Hz
Output voltage/current .................. 21 V d. c. / 3 A
The machine may exceed 85 dB (A). The operator
will require noise protection measures if this is
the case. The noise was measured in accordance
with EN 60745-1. The value of the vibrations emit-
ted by the handle was determined in accordance
with EN 60745-1.
The specifi ed vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equip-
ment is used and may exceed the specifi ed value
in exceptional circumstances.
The specifi ed vibration value can be used to
compare the equipment with other electric power
tools.
The specifi ed vibration value can be used for initi-
al assessment of a harmful eff ect.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
Anl_GE_CH_1846_Li_SPK7.indb 17 Anl_GE_CH_1846_Li_SPK7.indb 17
GB
........................ 64.8 dB
pA
............................ 84.8 dB
- 17 -
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.

5. Before starting the equipment

5.1 Installing the battery (Fig. 4)
Press the side pushlock buttons of the battery
pack as shown in Fig. 4 and push the battery
pack into the mount provided. When the battery
pack is positioned as in Fig. 1, make sure that the
pushlock buttons latch in place! To remove the
battery pack, proceed in reverse order.
5.2 Charging the battery (Fig. 5)
1. Take the battery pack out of the equipment.
Do this by pressing the pushlock buttons (Fi-
gure 2/Item 9).
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(5) into the mains socket outlet. The green
LED will then begin to flash.
3. Insert the battery pack (6) into the battery
charger (5).
4. In section "Charger indicator" you will find a
table with an explanation of the LED indicator
on the charger.
The battery pack can become a little warm during
the charging. This is normal.
If the battery pack fails to charge, check:
•
whether there is voltage at the socket outlet
•
whether there is good contact at the charging
contacts
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the power of the cordless hedge trim-
mer drops. Never fully discharge the battery pack.
This will cause it to develop a defect.
Battery capacity indicator (Fig. 6)
Press the switch for the battery capacity indicator
(Item A). The battery capacity indicator (Item B)
shows the charge status of the battery using 3
LEDs.
28.07.2016 09:36:29 28.07.2016 09:36:29